Si/Cu/P合金化对球墨铸铁组织与力学性能的影响

doi:10.13251/j.issn.0254-6051.2025.08.009

金属热处理 ›› 2025, Vol. 50 ›› Issue (8): 46-54.DOI: 10.13251/j.issn.0254-6051.2025.08.009

Si/Cu/P合金化对球墨铸铁组织与力学性能的影响

杨岳清^1,2, 杜宝帅^1,2, 杨超³, 蒋百灵³, 王倩³, 闫芝成^1,2

1.国网山东省电力公司电力科学研究院, 山东济南 250002;
2.山东省智能电网技术创新中心, 山东济南 250002;
3.西安理工大学材料科学与工程学院, 陕西西安 710048

收稿日期:2025-03-09 修回日期:2025-07-01 出版日期:2025-08-25 发布日期:2025-09-10
通讯作者: 杜宝帅,正高级工程师,博士,E-mail:dubaoshuai@163.com
作者简介:杨岳清(1993—),男,工程师,博士,主要研究方向为电工金属材料力学性能与变形损伤,E-mail:yueqing_yang@163.com。
基金资助:
国网山东省电力公司科技项目(520626230011)

Effect of Si/Cu/P alloying on microstructure and mechanical properties of nodular cast iron

Yang Yueqing^1,2, Du Baoshuai^1,2, Yang Chao³, Jiang Bailing³, Wang Qian³, Yan Zhicheng^1,2

1. State Grid Shandong Electric Power Research Institute, Jinan Shandong 250002, China;
2. Shandong Smart Grid Technology Innovation Center, Jinan Shandong 250002, China;
3. School of Materials Science and Engineering, Xi'an University of Technology, Xi'an Shaanxi 710048, China

Received:2025-03-09 Revised:2025-07-01 Online:2025-08-25 Published:2025-09-10

摘要/Abstract

摘要： 利用OM、SEM、XRD、洛氏硬度计、维氏硬度计及材料试验机,研究了Si、Cu与P含量和等温淬火工艺对球墨铸铁组织与力学性能的影响。结果表明,等温淬火组织均为奥铁体+球状石墨。随着等温温度的升高,针状铁素体尺寸增大,残留奥氏体含量增加。当等温温度为300 ℃时,球墨铸铁的综合力学性能最佳。在相同Si含量下,Cu和P元素的添加可以增加基体中石墨球的数量,提升石墨球圆整度,减小等温淬火球墨铸铁的针状铁素体尺寸,提升等温淬火球墨铸铁的强塑性。经300 ℃等温淬火,Si含量为1.1% 时,添加0.6%Cu的球墨铸铁获得最高屈服强度,可达1363 MPa。

关键词: 球墨铸铁, 等温淬火, 力学性能, 组织, 硅含量

Abstract: Effects of Si, Cu, and P contents and isothermal quenching process on the microstructure and mechanical properties of nodular cast iron were studied by using OM, SEM, XRD, Rockwell hardness tester, Vickers hardness tester, and material testing machine. The results indicate that the microstructure after isothermal quenching is composed of ausferrite and spherical graphite. As the isothermal temperature increases, the size of acicular ferrite increases and the retained austenite content increases. The comprehensive mechanical properties of nodular cast iron are optimal when the isothermal temperature is 300 ℃. Under the same Si content, the addition of Cu and P elements can increase the number of graphite nodules in the substrate, improve the roundness of graphite nodules, reduce the size of acicular ferrite in isothermal quenched nodular cast iron, and enhance the strength and plasticity of isothermal quenched nodular cast iron. Specifically, when the Si content is 1.1%, the addition of 0.6%Cu achieves the yield strength of 1363 MPa of the nodular cast iron isothermal quenched at 300 ℃.

Key words: nodular cast iron, isothermal quenching, mechanical properties, microstructure, silicon content

中图分类号:

TG143.5

杨岳清, 杜宝帅, 杨超, 蒋百灵, 王倩, 闫芝成. Si/Cu/P合金化对球墨铸铁组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 46-54.

Yang Yueqing, Du Baoshuai, Yang Chao, Jiang Bailing, Wang Qian, Yan Zhicheng. Effect of Si/Cu/P alloying on microstructure and mechanical properties of nodular cast iron[J]. Heat Treatment of Metals, 2025, 50(8): 46-54.

参考文献

[1] Wang Y P, Yan Q, Yang J R, et al. Can inter-provincial transmission reduce regional carbon emissions? Evidence from China[J]. Energy Policy, 2024, 184: 113915.
[2] Zeng M, Li H L, Ma M J, et al. Review on transaction status and relevant policies of southern route in China's West-East Power Transmission[J]. Renewable Energy, 2013, 60: 454-461.
[3] 顾建伟, 余辉, 陈维江, 等. ±1100 kV特高压直流线路无间隙线路避雷器雷电防护适用性研究[J]. 电瓷避雷器, 2023(6): 126-137.
Gu Jianwei, Yu Hui, Chen Weijiang, et al. Lightning protection applicability of gapless arrester in ±1100 kV UHV DC transmission lines[J]. Insulators and Surge Arresters, 2023(6): 126-137.
[4] 杨晓东, 谭恒. 输变电技术在智能电网中的应用[J]. 中国高新科技, 2023(21): 95-97.
Yang Xiaodong, Tan Heng. Application analysis of transmission and transformation technology in smart grid[J]. China High and New Technology, 2023(21): 95-97.
[5] 党乐, 郭金刚, 崔亚茹, 等. 架空输电线路金具材料研究现状及发展[J]. 电气技术, 2022, 23(4): 1-6.
Dang Le, Guo Jingang, Cui Yaru, et al. Research status and development of power fittings materials for transmission lines[J]. Electrical Engineering, 2022, 23(4): 1-6.
[6] 周海飞, 李凤瑞, 王河, 等. 连接金具用Q235钢表面激光合金化耐磨耐蚀涂层的组织及性能研究[J/OL]. 表面技术, 2024, 4(4): 1-14.
Zhou Haifei, Li Fengrui, Wang He, et al. Study on the microstructure and properties of laser surface alloying anti-wear/corrosion coating on Q235 steel surface for electric power fitting[J/OL]. Surface Technology, 2024, 4(4): 1-14.
[7] 曾萍, 刘志刚, 黄长勇, 等. 一种环链连接金具的摩擦磨损特性有限元仿真分析[J]. 湖南电力, 2023, 43(4): 90-94.
Zeng Ping, Liu Zhigang, Huang Changyong, et al. Finite element simulation of abrasive wear characteristics for a ring chain line fitting[J]. Hunan Electric Power, 2023, 43(4): 90-94.
[8] Sugishita J, Fujiyoshi S. The effect of cast iron graphite on friction and wear performance III: The lubricating effect of graphite under rolling-sliding contacts[J]. Wear, 1982, 77(2): 181-193.
[9] Andriollo T, Tiedje N, Hattel J. Distance map based micromechanical analysis of the impact of matrix heterogeneities on the yield stress of nodular cast iron[J]. Mechanics of Materials, 2020, 148: 103414.
[10] Chaengkham P, Srichandr P. Continuously cast ductile iron: Processing, structures, and properties[J]. Journal of Materials Processing Technology, 2011(8): 1372-1378.
[11] Ghaderi A R, Ahmadabadi M N, Ghasemi H M. Effect of graphite morphologies on the tribological behavior of austempered cast iron[J]. Wear, 2003(1): 410-416.
[12] Zhang Y, Cao Y, Huang G J, et al. Influence of martensite/bainite dual phase-content on the mechanical properties of EA4T high-speed axle steel[J]. Materials, 2023, 16(13): 4657.
[13] Ahmadabadi M N, Nategh S, Davami P. Wear behaviour of austempered ductile iron[J]. Cast Metals, 1991, 4(4): 188-194.
[14] Liu P, Bahadur S, Verhoeven J D. Friction and wear behavior of high silicon bainitic structures in austempered cast iron and steel[J]. Wear, 1990(1/2): 269-284.
[15] Kumar R, Dwivedi R K, Singh V P, et al. Influence of toughness and retained austenite on wear behaviour of carbide-free bainite in high silicon steel[J]. Transactions of the Indian Institute of Metals, 2023, 76(9): 2425-2434.
[16] Vaško A. Comparison of mechanical and fatigue properties of SiMo- and SiCu- types of nodular cast iron[J]. Materials Today: Proceedings, 2020, 32: 168-173.
[17] 耿国锋, 未永斌. 硅固溶强化铁素体基球墨铸铁性能研究进展[J]. 河北工业科技, 2023, 40(1): 67-74.
Geng Guofeng, Wei Yongbin. Research development in property of Si solution strengthened ferritic ductile iron[J]. Hebei Journal of Industrial Science and Technology, 2023, 40(1): 67-74.
[18] 常乐. 耐候角钢中Al元素分析影响因素研究[J]. 天津冶金, 2022(1): 66-69.
Chang Le. Study on influencing factors of Al element analysis in weathering angle steel[J]. Tianjin Metallurgy, 2022(1): 66-69.
[19] 秦树超, 董志强. 耐候钢的发展及技术难点浅析[C]//河北省2010年炼钢-连铸-轧钢生产技术与学术交流会论文集(上). 2010: 24-27.
[20] Yang P, Fu H, Absi R, et al. Improved corrosive wear resistance of carbidic austempered ductile iron by addition of Cu[J]. Materials Characterization, 2020, 168: 110577.
[21] König M, Wessén M. The influence of copper on microstructure and mechanical properties of compacted graphite iron[J]. International Journal of Cast Metals Research, 2009, 22(1-4): 164-167.
[22] 刘伟. 汽车发动机缸体铸造工艺及材质的研究[D]. 合肥: 合肥工业大学, 2009.
[23] Wetterfall S E, Fredriksson H, Hillert M. Solidification process of nodular cast iron[J]. Journal of Iron and Steel Research International, 1972(5): 323-333.
[24] 颜国君. 金属材料学[M]. 北京: 冶金工业出版社, 2019: 185.
[25] 杨超, 王倩, 蒋百灵, 等. 一种耐候抗磨损的特高压输电线用连接金具及其制备方法: 中国, CN116855820A[P]. 2023-10-10.
[26] 申志清, 田学雷, 郑洪亮, 等. 球墨铸铁石墨球核心组成及形核机制的研究[J]. 铸造, 2012, 61(4): 357-361.
Shen Zhiqing, Tian Xuelei, Zheng Hongliang, et al. Phase composition and nucleation mechanism of spheroidal graphite nucleus in ductile iron[J]. Foundry, 2012, 61(4): 357-361.
[27] 朱绍晨. 耐磨球铁在汽车冷作冲压模具中的应用[D]. 沈阳: 沈阳工业大学, 2015.
[28] 杨鹏辉. 含碳化物等温淬火球墨铸铁的组相调控机理研究[D]. 北京: 北京工业大学, 2021.

Si/Cu/P合金化对球墨铸铁组织与力学性能的影响

Effect of Si/Cu/P alloying on microstructure and mechanical properties of nodular cast iron

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	祁震, 梁丰瑞, 罗小兵, 柴锋, 葛启录, 展之德, 宋成民, 罗坤杰. 船用高强球扁钢的连续冷却转变与奥氏体相变动力学分析[J]. 金属热处理, 2025, 50(8): 1-7.
[2]	张翔宇, 张宇, 代春朵, 刘华松, 闫智然. 铌钒钛微合金化对热成形钢组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 14-19.
[3]	朱帅康, 暴嘉宁, 冯毅, 赵鑫, 蔡志辉. Fe-11Mn-2Al-2Si中锰钢的动态变形行为[J]. 金属热处理, 2025, 50(8): 30-34.
[4]	邢珂珂, 彭伟锋, 王金华, 张静, 张荣, 薛佳宁. 不同热加工方式下C286无磁不锈钢性能差异性分析[J]. 金属热处理, 2025, 50(8): 40-45.
[5]	张兵, 赵鸿金, 胡玉军, 叶俊峰, 梁小霞, 旷军平. 新能源汽车用电池托盘铝合金型材的力学性能与耐蚀性[J]. 金属热处理, 2025, 50(8): 63-70.
[6]	黄惠毅, 乐永康, 李飞龙, 廖斌, 吴烔. 微量B对6101铝合金组织与性能的影响[J]. 金属热处理, 2025, 50(8): 71-75.
[7]	那艳会, 王存宇, 冯桂萍, 周吉贞. 直线滚动导轨用55MnCr钢的感应淬火组织与硬度[J]. 金属热处理, 2025, 50(8): 76-79.
[8]	陈升平, 黄秋玉, 罗璇, 方向, 易出山, 贾新云, 黄朝晖. DZ406合金燃气涡轮工作叶片服役后的显微组织[J]. 金属热处理, 2025, 50(8): 80-84.
[9]	笪仲钟, 王为民, 万宇, 李文通, 亓海全, 姚小凤, 谢盈盈, 李欣欣. 模拟暴晒对DP590钢显微组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 85-90.
[10]	苑庆德, 朱治愿, 冯迪, 徐超凡, 徐锦文, 贾俊波, 王天宏. 长期时效对21-4NWNbMoCu合金组织和性能的影响[J]. 金属热处理, 2025, 50(8): 91-95.
[11]	马世朝, 闵小华, 高朋, 戴进财. 预变形与等温ω相的协同作用对Ti-10Mo合金力学性能的影响[J]. 金属热处理, 2025, 50(8): 96-102.
[12]	王冰, 孙瀚, 程战, 吴元科, 钟素娟, 龙伟民, 关常勇. 激光功率对18CrNiMo渗碳钢淬火层组织与性能的影响[J]. 金属热处理, 2025, 50(8): 103-109.
[13]	韩冰, 刘国龙, 李建英, 马晓杰, 刘帅, 冯运莉. 过时效温度对深冲双相钢组织、织构与性能的影响[J]. 金属热处理, 2025, 50(8): 110-117.
[14]	高超, 王旭, 蒋宏利, 王东梅, 岑耀东, 陈林. 回火温度对U20Mn贝氏体轨钢耐磨性的影响[J]. 金属热处理, 2025, 50(8): 118-126.
[15]	王潇维, 郭胤岑, 樊善明, 彭明军, 张帅博, 段永华, 周晓龙, 李萌蘖. 固溶时效处理对轧制Al-Mg-Si合金组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 137-143.