模拟暴晒对DP590钢显微组织与力学性能的影响

doi:10.13251/j.issn.0254-6051.2025.08.015

金属热处理 ›› 2025, Vol. 50 ›› Issue (8): 85-90.DOI: 10.13251/j.issn.0254-6051.2025.08.015

模拟暴晒对DP590钢显微组织与力学性能的影响

笪仲钟¹, 王为民², 万宇¹, 李文通¹, 亓海全¹, 姚小凤¹, 谢盈盈¹, 李欣欣¹

1.桂林理工大学材料科学与工程学院, 广西桂林 541004;
2.四川航空工业川西机器有限责任公司, 四川雅安 625000

收稿日期:2025-03-19 修回日期:2025-06-30 出版日期:2025-08-25 发布日期:2025-09-10
通讯作者: 亓海全,副教授,博士,E-mail:alexander_qi@163.com
作者简介:笪仲钟(1999—),女,硕士研究生,主要研究方向为先进高强度钢新材料开发应用及工艺,E-mail:dzhzhong@163.com。
基金资助:
广西科技重大专项(桂科AA22067079)

Effect of simulated sun exposure on microstructure and mechanical properties of DP590 steel

Da Zhongzhong¹, Wang Weimin², Wan Yu¹, Li Wentong¹, Qi Haiquan¹, Yao Xiaofeng¹, Xie Yingying¹, Li Xinxin¹

1. School of Materials Science and Engineering, Guilin University of Technology, Guilin Guangxi 541004, China;
2. Sichuan Aviation Industry Chuanxi Machinery Co., Ltd., Ya'an Sichuan 625000, China

Received:2025-03-19 Revised:2025-06-30 Online:2025-08-25 Published:2025-09-10

摘要/Abstract

摘要： 采用某商用冷轧DP590钢通过热处理方式进行模拟暴晒试验,探究车身用高强钢经长期反复暴晒后力学性能和显微组织变化。使用马弗炉设定10组不同时间不同温度的暴晒试验,通过拉伸试验机、扫描电镜对暴晒后试样进行分析。结果表明,随暴晒时间增加,试验钢的抗拉强度和屈服强度明显下降,其中暴晒60天的试样较原始母材屈服强度下降约60 MPa,而暴晒温度对强度影响并不显著;经暴晒后,试验钢显微组织仍由铁素体和马氏体组成,但马氏体分解,小角度晶界减少,致使DP590钢的综合力学性能均低于原材料,这将会对DP590钢所制结构件的服役安全性产生不利影响。

关键词: 双相钢, 车辆暴晒, 力学性能, 显微组织

Abstract: A commercial cold rolled DP590 steel was subjected to simulated sun exposure test by heat treatment, and the mechanical properties and microstructure changes of high strength steel for vehicle body after long-term repeated exposure were investigated. Ten groups of exposure tests at different temperatures for different time were set up by muffle furnace, and the specimens after exposure were analyzed by tensile testing machine and scanning electron microscope. The results show that the tensile strength and yield strength of the tested steel decrease obviously with the increase of exposure time, and the yield strength of the specimen exposed for 60 d decreases by about 60 MPa, while the effect of exposure temperature on the strength is not significant. After being heated, the microstructure of the tested steel is still composed of ferrite and martensite. The martensite decomposes and the low-angle grain boundaries decrease, the comprehensive mechanical properties of the tested DP590 steel are all lower than those of the raw materials, which will have adverse impact on the service safety of structural parts made of the DP590 steel.

Key words: dual-phase steel, vehicle exposure, mechanical properties, microstructure

中图分类号:

TG156

笪仲钟, 王为民, 万宇, 李文通, 亓海全, 姚小凤, 谢盈盈, 李欣欣. 模拟暴晒对DP590钢显微组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 85-90.

Da Zhongzhong, Wang Weimin, Wan Yu, Li Wentong, Qi Haiquan, Yao Xiaofeng, Xie Yingying, Li Xinxin. Effect of simulated sun exposure on microstructure and mechanical properties of DP590 steel[J]. Heat Treatment of Metals, 2025, 50(8): 85-90.

参考文献

[1] Frank Czerwinski. Current trends in automotive lightweighting strategies and materials[J]. Materials, 2021, 14(21): 6631.
[2] 娄元豪, 王优强, 邢照斌. 汽车轻量化研究进展[J]. 汽车工艺与材料, 2023(9): 1-7.
Lou Yuanhao, Wang Youqiang, Xing Zhaobin. Research progress on automotive lightweight[J]. Automobile Technology and Material, 2023(9): 1-7.
[3] Cui Xintao, Zhang Hongwei, Wang Shuxin, et al. Design of lightweight multi-material automotive bodies using new material performance indices of thin-walled beams for the material selection with crashworthiness consideration[J]. Materials and Design, 2011, 32(2): 815-821.
[4] 马鸣图, 吴宝榕. 双相钢物理和力学冶金[M]. 北京: 冶金工业出版社, 2009.
[5] 田志强, 唐荻, 江海涛, 等. 汽车用双相钢的研究与生产现状[J]. 机械工程材料, 2009, 33(4): 1-5.
Tian Zhiqiang, Tang Di, Jiang Haitao, et al, Research and production status of dual phase steels for automobiles[J]. Mechanical Engineering Materials, 2009, 33(4): 1-5.
[6] 陈平方, 余晓杰, 姜波. 汽车整车在中东热带沙漠环境下的大气暴晒试验研究[J]. 环境技术, 2022, 40(3): 90-92, 132.
Chen Pingfang, Yu Xiaojie, Jiang Bo. Experimental study on atmospheric exposure of vehicle under tropical desert environment in the middle east[J]. Environmental Technology, 2022, 40(3): 90-92, 132.
[7] 陈平方, 余晓杰, 陆挺. 整车自然暴晒与全光谱阳光模拟老化相关性研究[J]. 环境技术, 2020, 38(3): 70-73.
Chen Pingfang, Yu Xiaojie, Lu Ting. Study on the correlation between vehicle natural exposure and full-spectrum sunlight simulation aging[J]. Environmental Technology, 2020, 38(3): 70-73.
[8] 陈宇. 整车暴晒后温度极值区间及温度场分布研究[J]. 汽车测试报告, 2023(16): 158-160.
Chen Yu. Study on the extreme temperature range and temperature field distribution after vehicle exposure[J]. Automotive Test Report, 2023(16): 158-160.
[9] Zamani Mehran, Mirzadeh Hamed, Maleki Mehdi. Enhancement of mechanical properties of low carbon dual phase steel via natural aging[J]. Materials Science and Engineering A, 2018, 734: 178-183.
[10] 何建勇, 顾国微, 龙玉全. 汽车侧面碰撞法规的研究与分析[J]. 专用汽车, 2024(2): 1-3.
He Jianyong, Gu Guowei, Long Yuquan. Research and analysis of vehicle side impact regulations[J]. Special Purpose Vehicle, 2024(2): 1-3.
[11] 荣升格, 施帆君, 齐纪元, 等. 汽车车身结构对汽车被动安全性能的影响[J]. 汽车与新动力, 2023, 6(5): 17-20.
Rong Shengge, Shi Fanjun, Qi Jiyuan, et al. Influence of automobile body structure on passive safety performance of automobile[J]. Automobile and New Power, 2023, 6(5): 17-20.
[12] 缑瑞宾, 徐浩, 于敏, 等. 高温暴晒和火灾服役条件下高强钢DP800的力学性能变化规律[J]. 材料热处理学报, 2024, 45(3): 148-157.
Gou Ruibin, Xu Hao, Yu Min, et al. Changes in mechanical properties of high strength steel DP800 under high temperature exposure and fireservice conditions[J]. Transactions of Materials and Heat Treatment, 2024, 45(3): 148-157.
[13] Waterschoot T, De Cooman B C, Vandeputte S, et al. Neutron diffraction study of the low-temperature ageing of martensite in dual-phase steel[J]. International Journal of Materials Research, 2022, 94(4): 424-435.
[14] Ebrahimian A, Banadkouki S S G. Mutual mechanical effects of ferrite and martensite in a low alloy ferrite-martensite dual phase steel[J]. Journal of Alloys and Compounds, 2017, 708: 43-54.
[15] 史美堂. 金属材料及热处理[M]. 上海: 上海科学技术出版社, 1981.

模拟暴晒对DP590钢显微组织与力学性能的影响

Effect of simulated sun exposure on microstructure and mechanical properties of DP590 steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张翔宇, 张宇, 代春朵, 刘华松, 闫智然. 铌钒钛微合金化对热成形钢组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 14-19.
[2]	邢珂珂, 彭伟锋, 王金华, 张静, 张荣, 薛佳宁. 不同热加工方式下C286无磁不锈钢性能差异性分析[J]. 金属热处理, 2025, 50(8): 40-45.
[3]	杨岳清, 杜宝帅, 杨超, 蒋百灵, 王倩, 闫芝成. Si/Cu/P合金化对球墨铸铁组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 46-54.
[4]	张兵, 赵鸿金, 胡玉军, 叶俊峰, 梁小霞, 旷军平. 新能源汽车用电池托盘铝合金型材的力学性能与耐蚀性[J]. 金属热处理, 2025, 50(8): 63-70.
[5]	陈升平, 黄秋玉, 罗璇, 方向, 易出山, 贾新云, 黄朝晖. DZ406合金燃气涡轮工作叶片服役后的显微组织[J]. 金属热处理, 2025, 50(8): 80-84.
[6]	苑庆德, 朱治愿, 冯迪, 徐超凡, 徐锦文, 贾俊波, 王天宏. 长期时效对21-4NWNbMoCu合金组织和性能的影响[J]. 金属热处理, 2025, 50(8): 91-95.
[7]	马世朝, 闵小华, 高朋, 戴进财. 预变形与等温ω相的协同作用对Ti-10Mo合金力学性能的影响[J]. 金属热处理, 2025, 50(8): 96-102.
[8]	韩冰, 刘国龙, 李建英, 马晓杰, 刘帅, 冯运莉. 过时效温度对深冲双相钢组织、织构与性能的影响[J]. 金属热处理, 2025, 50(8): 110-117.
[9]	高超, 王旭, 蒋宏利, 王东梅, 岑耀东, 陈林. 回火温度对U20Mn贝氏体轨钢耐磨性的影响[J]. 金属热处理, 2025, 50(8): 118-126.
[10]	王潇维, 郭胤岑, 樊善明, 彭明军, 张帅博, 段永华, 周晓龙, 李萌蘖. 固溶时效处理对轧制Al-Mg-Si合金组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 137-143.
[11]	费海洋, 邹乾坤, 杨永, 宋孟, 李天瑞. 冷轧压下率对Hastelloy C-276合金组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 150-156.
[12]	贾虹锋, 胡宝佳, 肖广耀, 田亚强, 陈连生. 回火温度对舰船用含Cu高强钢组织与性能的影响[J]. 金属热处理, 2025, 50(8): 215-219.
[13]	李浩, 李杨, 杨峰, 李云超, 王海龙, 郝蕾, 王玉慧, 许强. 均热温度对1200 MPa镀锌双相钢微观组织与力学性能的影响[J]. 金属热处理, 2025, 50(8): 225-229.
[14]	龚雪玲, 顾剑锋, 王婧, 袁志钟, 王琴, 史有森. GCr15钢的碳氮共渗工艺参数及其对微观组织与性能的影响[J]. 金属热处理, 2025, 50(7): 1-9.
[15]	张皓月, 唐正友, 崔峰, 张瀚文, 王镇轩. 固溶温度对Fe-Mn-Al-C奥氏体低密度钢组织与性能的影响[J]. 金属热处理, 2025, 50(7): 18-23.