基于JMatPro软件分析V含量对水电钢热处理性能的影响

doi:10.13251/j.issn.0254-6051.2025.10.012

金属热处理 ›› 2025, Vol. 50 ›› Issue (10): 79-86.DOI: 10.13251/j.issn.0254-6051.2025.10.012

基于JMatPro软件分析V含量对水电钢热处理性能的影响

刘悦¹, 杨铖龙¹, 杨武杰¹, 唐哲萱¹, 张朋², 张山²

1.华北理工大学机械工程学院, 河北唐山 063210;
2.华北理工大学冶金与能源学院, 河北唐山 063210

收稿日期:2025-04-28 修回日期:2025-08-15 出版日期:2025-10-25 发布日期:2025-11-04
通讯作者: 张朋,正高级工程师,博士,E-mail: zhangpengysu@126.com
作者简介:刘悦(1990—),女,讲师,博士,主要研究方向为金属材料加工与热处理,E-mail: liuyueneu@163.com。
基金资助:
河北省创新能力提升计划(24461002D);华北理工大学大学生创新创业训练计划(S202410081019)

Effect of vanadium content on heat-treated properties of hydropower steel based on JMatPro analysis

Liu Yue¹, Yang Chenglong¹, Yang Wujie¹, Tang Zhexuan¹, Zhang Peng², Zhang Shan²

1. College of Mechanical Engineering, North China University of Science and Technology, Tangshan Hebei 063210, China;
2. College of Metallurgy and Energy, North China University of Science and Technology, Tangshan Hebei 063210, China

Received:2025-04-28 Revised:2025-08-15 Online:2025-10-25 Published:2025-11-04

摘要/Abstract

摘要： 利用JMatPro计算软件模拟了3种不同V含量(0、0.05%和0.09%)的08MnCrMoVR水电钢的平衡相组成、TTA、TTT和CCT曲线、Jominy淬透性和回火工艺参数等,研究了该钢在达到服役性能的条件下,V含量对其显微组织与力学性能的影响,并根据模拟结果对0.05%V水电钢进行了淬火回火试验。结果表明,随着钢中V含量的升高,其力学性能、淬火性能和淬透性逐渐提高。经900 ℃×1 h淬火和600 ℃×1.5 h回火后0.05V%水电钢的组织为均匀细小的回火索氏体,并且其力学性能与JMatPro软件模拟结果基本一致。

关键词: JMatPro软件, V含量, 水电钢, 热处理

Abstract: Equilibrium phase composition, TTA, TTT and CCT curves, Jominy hardenability and tempering process parameters of 08MnCrMoVR hydropower steels with vanadium contents of 0, 0.05% and 0.09%, respectively, were simulated by JMatPro software. The effect of vanadium content on the microstructure and mechanical properties of the steel on the basis of meeting the service performance requirements was investigated, and quenching and tempering test of 0.05%V hydropower steel was carried out according to the simulation results. The results show that as the vanadium content in the hydropower steel increases, the mechanical properties, quenching property and hardenability are gradually improved. The microstructure of the 0.05V% hydropower steel after quenching at 900 ℃ for 1 h and tempering at 600 ℃ for 1.5 h is uniform and fine tempered martensite, and its mechanical properties are basically consistent with the simulation results of JMatPro software.

Key words: JMatPro software, vanadium content, hydropower steel, heat treatment

中图分类号:

TG156.31

刘悦, 杨铖龙, 杨武杰, 唐哲萱, 张朋, 张山. 基于JMatPro软件分析V含量对水电钢热处理性能的影响[J]. 金属热处理, 2025, 50(10): 79-86.

Liu Yue, Yang Chenglong, Yang Wujie, Tang Zhexuan, Zhang Peng, Zhang Shan. Effect of vanadium content on heat-treated properties of hydropower steel based on JMatPro analysis[J]. Heat Treatment of Metals, 2025, 50(10): 79-86.

参考文献

[1] 张博庭. 认清水电在实现“双碳”中的重要作用[J]. 工程研究: 跨学科视野中的工程, 2024, 16(2): 147-160.
Zhang Boting. On the important role of hydropower in achieving “Carbon Peak and Neutrality” goals[J]. Journal of Engineering Studies, 2024, 16(2): 147-160.
[2] 李晓超, 谢威威, 秦蓉, 等. 水电站故障监测与分析系统研究综述[J]. 水科学与工程技术, 2021(5): 85-89.
Li Xiaochao, Xie Weiwei, Qin Rong, et al. Summary of the research on fault monitoring and analysis system of hydropower station[J]. Water Sciences and Engineering Technology, 2021(5): 85-89.
[3] Pan Z D, Wang E M, Wu H B. Precipitation behavior and strengthening—toughening mechanism of Nb micro-alloyed direct-quenched and tempered 1000 MPa grade high-strength hydropower steel[J]. Metals, 2024, 14(7): 794.
[4] Chen J, Li C S, Jin X, et al. Effect of quenching process on microstructures and mechanical properties of Fe-0.9Mn-0.5Cr-2.4Ni-0.5Mo-C steel[J]. Journal of Materials Engineering and Performance, 2018, 27(4): 1505-1513.
[5] Tang Z L, Guo R, Zhang Y, et al. Continuous cooling transformation of under-cooled austenite of SXQ500/550DZ35 hydropower steel[J]. Metals, 2021, 11(10): 1562.
[6] 李超群, 赵千水, 张凯伦. 应用JMatPro软件对重载齿轮用钢17CrNiMo6的分析[J]. 金属世界, 2024(3): 25-28.
Li Chaoqun, Zhao Qianshui, Zhang Kailun. Analysis of 17CrNiMo6 steel for overloaded gear using JMatPro software[J]. Metal World, 2024(3): 25-28.
[7] 盛伟, 陈天运, 李志, 等. 基于JMatPro软件的超高强度钢强度设计[J]. 金属热处理, 2017, 42(6): 157-160.
Sheng Wei, Chen Tianyun, Li Zhi, et al. Strength design of ultra-high strength steel based on JMatPro software[J]. Heat Treatment of Metals, 2017, 42(6): 157-160.
[8] 马蓼奕, 杜青胤, 李世键, 等. 利用JMatPro软件模拟计算16CrSiNi钢热处理参数及热物理性能[J]. 金属热处理, 2024, 49(7): 42-46.
Ma Liaoyi, Du Qingyin, Li Shijian, et al. Simulation and calculation of heat treatment parameters and thermophysical properties of 16CrSiNi steel using JMatPro software[J]. Heat Treatment of Metals, 2024, 49(7): 42-46.
[9] 钟流发, 刘祚时, 高秀琴, 等. 基于JMatPro与ANSYS联合仿真的变速器齿轮轴选材和热处理工艺改进设计[J]. 机械设计与研究, 2020, 36(5): 84-88.
Zhong Liufa, Liu Zuoshi, Gao Xiuqin, et al. Material selection and heat treatment process improvement design of transmission gear shaft based on joint simulation of JMatPro and ANSYS[J]. Machine Design and Research, 2020, 36(5): 84-88.
[10] 吴冰洁, 朱明冬, 王留兵, 等. 基于JMatPro计算的91钢热处理工艺研究[J]. 热处理, 2024, 39(5): 6-8, 14.
Wu Bingjie, Zhu Mingdong, Wang Liubing, et al. Research on heat treatment process for 91 steel based on JMatPro calculation[J]. Heat Treatment, 2024, 39(5): 6-8, 14.
[11] 代玉杰, 王魁. 利用JMatPro软件进行C55E钢链板等温淬火工艺的研究[J]. 机械传动, 2024, 48(6): 147-152.
Dai Yujie, Wang Kui. Study on the isothermal quenching process ofC55E steel chain plates with JMatPro software[J]. Journal of Mechanical Transmission, 2024, 48(6): 147-152.
[12] 赵玥. 钢的TTT曲线测定方法研究[J]. 大型铸锻件, 2017(6): 35-37.
Zhao Yue. Research on test method of TTT diagram of steel[J]. Heavy Casting and Forging, 2017(6): 35-37.
[13] 蒋辉, 赵爱民, 裴伟, 等. 低合金耐磨钢的CCT曲线与马氏体相变原位观察[J]. 材料热处理学报, 2022, 43(11): 143-150.
Jiang Hui, Zhao Aimin, Pei Wei, et al. Continuous cooling transformation curve of low alloy wear-resistant steel and in-situ observation of its martensitic transformation[J]. Transactions of Materials and Heat Treatment, 2022, 43(11): 143-150.
[14] 杨维宇, 魏晓东, 白雅琼, 等. 微量稀土Ce对DX51D+Z低碳钢连续冷却转变曲线的影响[J]. 金属热处理, 2024, 49(10): 234-238.
Yang Weiyu, Wei Xiaodong, Bai Yaqiong, et al. Effect of trace rare earth Ce on continuous cooling transformation curve of DX51D+Z low carbon steel[J]. Heat Treatment of Metals, 2024, 49(10): 234-238.
[15] 庄巧玲. 基于JMatPro软件的ZG70CrMo钢的热处理工艺研究[J]. 中国铸造装备与技术, 2020, 55(5): 70-74.
Zhuang Qiaoling. Research on heat treatment process of ZG70CrMo steel on the basis of JMatPro software[J]. China Foundry Machinery and Technology, 2020, 55(5): 70-74.
[16] 尹慧, 翟瑞志, 滕树满. 基于JMatPro的热锻模具钢55NiCrMoV7热物理性能预测[J]. 模具制造, 2022, 22(5): 80-83.
Yin Hui, Zhai Ruizhi, Teng Shuman. Prediction of thermophysical properties of hot forging die steel 55NiCrMoV7 based on JmatPro[J]. Die and Mould Manufacture, 2022, 22(5): 80-83.
[17] Luo P, Li X J, Zhang W L, et al. The study of phase transformation behaviors for 38MnB5Nb ultra high-strength steel by CCT curves and TTT curves[J]. Metals, 2023, 13(2): 190.
[18] 王陆军, 查建军, 朱建新, 等. 淬透性在热处理实践中的应用[J]. 热处理技术与装备, 2022, 43(2): 54-59.
Wang Lujun, Zha Jianjun, Zhu Jianxin, et al. Application of hardenability in heat treatment practice[J]. Heat Treatment Technology and Equipment, 2022, 43(2): 54-59.
[19] 张国强, 王毛球, 曹燕光, 等. 钢的淬透性预测模型研究进展[J]. 金属热处理, 2019, 44(4): 224-228.
Zhang Guoqiang, Wang Maoqiu, Cao Yanguang, et al. Review on hardenability prediction models of steels[J]. Heat Treatment of Metals, 2019, 44(4): 224-228.
[20] 吕超然, 史超, 蒋伟斌, 等. Al对42CrMo螺栓钢淬透性的影响[J]. 金属热处理, 2020, 45(10): 164-170.
Lü Chaoran, Shi Chao, Jiang Weibin, et al. Effect of Al on hardenability of 42CrMo bolt steel[J]. Heat Treatment of Metals, 2020, 45(10): 164-170.

基于JMatPro软件分析V含量对水电钢热处理性能的影响

Effect of vanadium content on heat-treated properties of hydropower steel based on JMatPro analysis

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	伊静, 董会, 王飞, 李鹏宇, 张永杰, 冯玉坤. 感应热处理超音速火焰喷涂NiCrBSiFe涂层的组织与性能[J]. 金属热处理, 2025, 50(9): 12-18.
[2]	黄亮, 马辉, 王晓东, 包喜荣. 基于TMCP的P92钢管的在线形变热处理[J]. 金属热处理, 2025, 50(9): 132-139.
[3]	何苗, 武晓峰, 董志强, 王端, 索忠源. 淬火温度对斗齿用35CrMnSi2钢组织与性能的影响[J]. 金属热处理, 2025, 50(9): 191-194.
[4]	孟凡西, 魏建华, 曹国钦, 潘慧超, 杜学山. 27SiMn钢连接头弯曲失效分析及热处理工艺优化[J]. 金属热处理, 2025, 50(9): 244-249.
[5]	任奕同, 方琪, 郭洪, 孙伟, 贺进明, 李岩峰. 铀及铀合金组织演变研究进展[J]. 金属热处理, 2025, 50(9): 317-325.
[6]	贾桂龙, 张航, 饶庆东, 郑许, 李锦婷, 覃丽萍, 何克准, 罗超庆. 航天用2A12铝合金蒙皮板气垫悬浮式热处理工艺[J]. 金属热处理, 2025, 50(8): 127-136.
[7]	苏文博, 石如星, 秦红付, 王义海, 郑三妹, 董超, 李岩, 李圣. 核电压力容器用SA508-3钢厚截面锻件的热处理模拟[J]. 金属热处理, 2025, 50(8): 272-277.
[8]	杨栋杰, 白峭峰, 欧阳昌耀. 热处理对激光熔覆Fe基合金涂层组织与耐磨性的影响[J]. 金属热处理, 2025, 50(8): 286-291.
[9]	熊峰, 周炜, 邓辉, 李时春, 唐思文, 颜建辉. 基于超星学习通的混合教学模式在“金属热处理原理与工艺”课程的改革与实践[J]. 金属热处理, 2025, 50(8): 309-313.
[10]	甘婵, 陈懿, 张义飞, 臧千昊, 陈洪美. 固溶处理对Mg-6Gd-3Y-1.5Zn-0.6Zr稀土镁合金组织的影响[J]. 金属热处理, 2025, 50(7): 73-80.
[11]	邢梦楠, 欧阳鑫, 胡昕明, 刘晨希, 白云峰, 王勇, 杨成, 王晓航. 316H奥氏体不锈钢中δ-铁素体的变化规律[J]. 金属热处理, 2025, 50(7): 133-140.
[12]	黎柏康, 秦翔智, 赵佳蕾, 李兵, 赵巍, 章晶林, 周毅, 李瑞霞. Zn、Mg含量对Al-Zn-Mg-Cu合金组织与性能的影响[J]. 金属热处理, 2025, 50(7): 218-225.
[13]	顾为杰, 于敏, 邓名, 王维俊, 秦经刚, 秦汝祥. 导体性能研究平台Nb₃Sn线圈的热处理[J]. 金属热处理, 2025, 50(7): 322-327.
[14]	王桂茂, 董小虹, 姚锡凡, 卢泽坚, 杨文茵. 智能制造在热处理企业的实践应用[J]. 金属热处理, 2025, 50(7): 339-343.
[15]	谢善, 任率, 林思宇. 1Cr16Co5Ni2MoWVNbN马氏体不锈钢锻件组织偏析原因分析[J]. 金属热处理, 2025, 50(6): 119-124.