淬火工艺对渗碳18Cr2Ni4WA钢采煤机行走轮冲击性能的影响

doi:10.13251/j.issn.0254-6051.2025.03.011

金属热处理 ›› 2025, Vol. 50 ›› Issue (3): 69-73.DOI: 10.13251/j.issn.0254-6051.2025.03.011

淬火工艺对渗碳18Cr2Ni4WA钢采煤机行走轮冲击性能的影响

何潇^1,2, 许鸿翔², 师陆冰², 赵少甫², 戎泽玉², 关鹤², 陈治²

1.中国机械总院集团郑州机械研究所有限公司, 河南郑州 450001;
2.郑机所(郑州)传动科技有限公司, 河南郑州 450001

收稿日期:2024-11-30 修回日期:2025-01-28 出版日期:2025-03-25 发布日期:2025-05-14
通讯作者: 许鸿翔,正高级工程师,博士研究生,E-mail:13838005005@163.com
作者简介:何潇(1996—),女,硕士研究生,主要研究方向为金属材料热处理工艺,E-mail:15637267734@163.com。
基金资助:
国家重点研发计划(2023YFB3408004)

Effect of quenching process on impact property of carburized 18Cr2Ni4WA steel shearer walking wheel

He Xiao^1,2, Xu Hongxiang², Shi Lubing², Zhao Shaofu², Rong Zeyu², Guan He², Chen Zhi²

1. China Academy of Machinery Zhengzhou Research Institute of Mechanical Engineering Co., Ltd., Zhengzhou Henan 450001, China;
2. Zhengzhou Research Institute of Mechanical Engineering Co., Ltd., Zhengzhou Henan 450001, China

Received:2024-11-30 Revised:2025-01-28 Online:2025-03-25 Published:2025-05-14

摘要/Abstract

摘要： 研究了淬火工艺对18Cr2Ni4WA钢渗碳淬火采煤机行走轮冲击性能的影响,通过对18Cr2Ni4WA钢采煤机行走轮进行渗碳热处理后,再分别进行780、800、830 ℃油淬,最后经-60 ℃冷处理2 h后继续180 ℃回火15 h完成全部热处理工艺,热处理后对试样进行力学性能和显微组织检测。结果表明:降低淬火温度,行走轮心部硬度明显降低,心部冲击性能大幅提升。采用亚温淬火工艺,淬火温度为780 ℃时,使采煤机行走轮满足表面硬度要求的同时提高心部冲击性能,显微组织由板条马氏体+铁素体+贝氏体及残留奥氏体组成,心部冲击性能大幅提升,冲击吸收能量达到108 J,实现渗碳淬火行走轮心部冲击性能的提升。

关键词: 18Cr2Ni4WA钢, 行走轮, 渗碳, 亚温淬火, 冲击性能

Abstract: The effect of quenching process on impact property of the carburized 18Cr2Ni4WA steel shearer walking wheels was investigated. After carburizing heat treatment, the 18Cr2Ni4WA steel shearer walking wheels were oil-quenched at 780, 800 and 830 ℃, respectively, and finally cryogenic treated at -60 ℃ for 2 h, then tempered at 180 ℃ for 15 h. After the heat treatment, the mechanical properties and microstructure of the specimens were tested. The results show that the hardness of the core of the walking wheel is significantly reduced, while the impact property of the core is greatly improved when the quenching temperature is reduced. By adopting intercritical quenching process, when the quenching temperature is 780 ℃, the shearer walking wheel can meet the surface hardness requirements and improve the impact property of the core, and the microstructure is composed of lath martensite, bainite, ferrite and retained austenite, and the impact property of the core is greatly improved with impact absorbed energy of 108 J, achieving the improvement of the core of the impact property of the carburized and quenched walking wheel.

Key words: 18Cr2Ni4WA steel, walking wheel, carburizing, intercritical quenching, impact property

中图分类号:

TG156.31

何潇, 许鸿翔, 师陆冰, 赵少甫, 戎泽玉, 关鹤, 陈治. 淬火工艺对渗碳18Cr2Ni4WA钢采煤机行走轮冲击性能的影响[J]. 金属热处理, 2025, 50(3): 69-73.

He Xiao, Xu Hongxiang, Shi Lubing, Zhao Shaofu, Rong Zeyu, Guan He, Chen Zhi. Effect of quenching process on impact property of carburized 18Cr2Ni4WA steel shearer walking wheel[J]. Heat Treatment of Metals, 2025, 50(3): 69-73.

参考文献

[1] 赵武, 李德昌, 刘威, 等. 采煤机行走轮断裂原因分析及改进措施[J]. 煤矿机械, 2015, 36(5): 308-309.
Zhao Wu, Li Dechang, Liu Wei, et al. Analysis on fracture and improve method of shearer wheel[J]. Coal Mining Machinery, 2015, 36(5): 308-309.
[2] 侯家平, 潘涛, 朱莹光, 等. 临界淬火工艺对9Ni低温钢力学性能及精细组织的影响[J]. 材料热处理学报, 2014, 35(10): 88-93.
Hou Jiaping, Pan Tao, Zhu Yingguang, et al. Effect of intercritical quenching process on mechanical property and microstructure of 9Ni cryogenic steel[J]. Transactions of Materials and Heat Treatment, 2014, 35(10): 88-93.
[3] 吴玉萍, 肖昌利. 低合金钢亚温淬火强韧化研究[J]. 理化检验(物理分册), 1997, 33(2): 11-12, 46.
Wu Yuping, Xiao Changli. Study of the strengthening and toughening of low-alloy steel after subnormal temperature quenching[J]. Physical Testing and Chemical Analysis Part A: Physical Testing, 1997, 33(2): 11-12, 46.
[4] 刘云旭. 金属热处理原理[M]. 北京: 机械工业出版社, 1998.
[5] 唐明华, 汪新衡, 赵建明. 26CrMoNbTiB 钻杆用钢亚温淬火强韧化工艺[J]. 金属热处理, 2018, 43(5): 184-189.
Tang Minghua, Wang Xinheng, Zhao Jianming. Intercritical quenching process of 26CrMoNbTiB drill pipe steel for strengthening and toughening[J]. Heat Treatment of Metals, 2018, 43(5): 184-189.
[6] 王传雅, 丁志敏. 18Cr2Ni4WA钢渗碳后亚温淬火的研究[J]. 机车车辆工艺, 1986(3): 13-19.
[7] 刘志强, 李晓红, 马彪, 等. 热处理工艺对 30CrMnSi 钢冲击性能的影响[J]. 金属热处理, 2015, 40(4): 74-76.
Liu Zhiqiang, Li Xiaohong, Ma Biao, et al. Effect of heat treatment on impact property of 30CrMnSi steel[J]. Heat Treatment of Metals, 2015, 40(4): 74-76.
[8] 郎雪琴, 代琨. 亚温淬火回火的30CrMoA钢的显微组织和力学性能[J]. 热处理, 2023, 38(4): 44-45.
Lang Xueqin, Dai Kun. Microstructure and mechanical properties of 30CrMoA steel after sub-critical quenching and tempering[J]. Heat Treatment, 2023, 38(4): 44-45.
[9] 覃展鹏, 王红鸿, 童志, 等. 亚温淬火工艺对低碳低合金高强钢组织及性能的影响[J]. 材料热处理学报, 2017, 38(9): 142-147.
Qin Zhanpeng, Wang Honghong, Tong Zhi, et al. Influence of lamellarizing process on microstructure and properties of low carbon low alloy high-strength steel[J]. Transactions of Materials and Heat Treatment, 2017, 38(9): 142-147.
[10] 钟宁. 高强度 Q＆P 钢和 Q-P-T 钢的研究[D]. 上海: 上海交通大学, 2009.
Zhong Ning. Research on high strength Q&P and Q-P-T steels[D]. Shanghai: Shanghai Jiao Tong University, 2009.
[11] De Knijf D, Petrov R, FÖjer C, et al. Effect of fresh martensite on the stability of retained austenite in quenching and partitioning steel[J]. Materials Science and Engineering A, 2014, 615: 107-115.
[12] Han J, da Silva A K, Ponge D, et al. The effects of prior austenite grain boundaries and microstructural morphology on the impact toughness of intercritically annealed medium Mn steel[J]. Acta Materialia, 2017, 122: 199-206.
[13] Takahiro K, Akio O, Osamu T. Properties of high toughness 9%Ni heavy section steel plate and its applicability to 200 000 kl LNG storage tanks[J]. Kawasaki Steel Technical Report, 1999, 40: 72-79.

[1]	金帅, 王会强, 崔建英, 王艳山, 闫学兰, 李文翔. 基于BP神经网络预测热处理后35CrMoA钢的低温冲击性能[J]. 金属热处理, 2025, 50(3): 125-131.
[2]	石磊, 田鹏勇, 温国强, 魏明江, 赵宇. 淬火工艺对铁素体/马氏体双相钢组织与性能的影响[J]. 金属热处理, 2025, 50(3): 138-142.
[3]	陈为浩, 许自宽, 谷雪忠, 杨卯生, 王斌, 张鹏, 张哲峰. 渗碳处理高强齿轮钢BG801的高温疲劳行为[J]. 金属热处理, 2025, 50(3): 255-262.
[4]	谢小春, 胡静. 汽车用驻车棘轮制造过程中裂纹形成原因分析[J]. 金属热处理, 2025, 50(3): 297-302.
[5]	马丽娜, 王啸宇, 聂舒诺, 何嘉琪, 欧阳思亦, 牛赛, 吴萌. 石油钻探用贝氏体非调质钢管的热轧工艺[J]. 金属热处理, 2025, 50(2): 225-229.
[6]	陈晟楠, 彭睿智, 吴晓春. 热处理工艺对SDP80C钢组织及性能的影响[J]. 金属热处理, 2025, 50(2): 241-246.
[7]	于朋翰, 严昊明, 杨帅, 于兴福, 刘永吉, 代友贵. 扩散时间对真空低压渗碳20CrMnTi钢组织与硬度的影响[J]. 金属热处理, 2025, 50(2): 251-255.
[8]	肖结良, 孙浩, 李飞, 胡平, 解扬, 陈旌钢. 正火工艺对含Cu大型球墨铸铁行走轮组织和性能的影响[J]. 金属热处理, 2025, 50(2): 256-259.
[9]	李瑶, 张伟, 李朝青. 18CrNiMo7-6钢中小模数齿轮的渗碳淬火处理[J]. 金属热处理, 2025, 50(2): 260-263.
[10]	何潇, 许鸿翔, 师陆冰, 陈生超, 李子岩, 戎泽玉, 李福利. 采煤机行走轮的常见失效问题及应对策略[J]. 金属热处理, 2025, 50(2): 304-311.
[11]	李忠波, 胡海江, 何平, 任可, 袁清, 吴润. 淬火和回火温度对Cr-Mo系耐磨钢组织及力学性能的影响[J]. 金属热处理, 2025, 50(1): 88-96.
[12]	王秉楠, 贾玉鑫, 王姗姗, 张亚辉. 高淬透性高碳铬轴承钢的组织与性能[J]. 金属热处理, 2024, 49(9): 31-35.
[13]	李朝青, 张伟, 李瑶. 井式炉渗碳淬火钢件表面炭黑问题分析[J]. 金属热处理, 2024, 49(9): 265-267.
[14]	赵厚锐, 刘克, 樊朋煜, 欧阳雪枚, 杨兵, 翟鹏远. 20Cr2Ni4A钢转向齿轮渗碳淬火工艺改进[J]. 金属热处理, 2024, 49(8): 189-194.
[15]	邓小虎, 宋汶娟, 凡园园, 郭晶玉, 王会珍, 周乐育, 徐跃明, 巨东英. 20CrMnTi钢真空低压渗碳过程数值模拟[J]. 金属热处理, 2024, 49(8): 220-224.

淬火工艺对渗碳18Cr2Ni4WA钢采煤机行走轮冲击性能的影响

Effect of quenching process on impact property of carburized 18Cr2Ni4WA steel shearer walking wheel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价