热处理对高Co、高V粉末高速钢PM60碳化物析出的影响

doi:10.13251/j.issn.0254-6051.2024.03.012

金属热处理 ›› 2024, Vol. 49 ›› Issue (3): 68-76.DOI: 10.13251/j.issn.0254-6051.2024.03.012

热处理对高Co、高V粉末高速钢PM60碳化物析出的影响

殷锦华^1,2, 祝柏林¹, 胡木林², 彭会^1,2

1.武汉科技大学省部共建耐火材料与冶金国家重点实验室, 湖北武汉 430081;
2.湖北黄石科创模具技术研究院有限公司, 湖北黄石 435000

收稿日期:2023-09-10 修回日期:2024-01-18 出版日期:2024-03-25 发布日期:2024-04-24
通讯作者: 祝柏林,教授,博士,E-mail:blzhu@wust.edu.cn
作者简介:殷锦华(1998—),男,硕士研究生,主要研究方向为粉末冶金高速钢,E-mail:1875237832@qq.com。

Effect of heat treatment process on carbide precipitation in high Co and high V high-speed steel PM60

Yin Jinhua^1,2, Zhu Bailin¹, Hu Mulin², Peng Hui^1,2

1. State Key Laboratory of Refractory Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan Hubei 430081, China;
2. Hubei Huangshi Kechuang Mold Technology Research Institute Co., Ltd., Huangshi Hubei 435000, China

Received:2023-09-10 Revised:2024-01-18 Online:2024-03-25 Published:2024-04-24

摘要/Abstract

摘要： PM60高速钢是通过粉末冶金方法制备,与普通高速钢相比,含有大量的Co元素,可以促进二次碳化物的析出。PM60高速钢在1120、1150、1180和1210 ℃淬火并油冷,然后在540、560和580 ℃分别进行3次回火。热处理结束之后,通过金相显微镜、扫描电镜、洛氏硬度计对热处理后PM60高速钢显微组织、析出相和硬度进行分析,结合JMatpro热力学计算软件研究淬火和回火热处理前后样品中碳化物的种类、形貌、成分、分布以及析出行为。结果表明,原来的析出相为MC、M₆C、M₂₃C₆和M₇C₃相,经热处理后为MC和M₆C相。经过能谱分析发现,这两种类型的碳化物,一类是颜色较暗的富V类碳化物,另一类是颜色较亮的富W、Mo类碳化物。淬火过程中部分碳化物溶解,回火过程中有细小弥散分布二次碳化物析出。在1180 ℃淬火+540 ℃回火条件下,材料硬度最高。

关键词: PM60高速钢, 粉末冶金, 碳化物, 热处理, 析出

Abstract: Compared with ordinary high speed steels, PM60 high-speed steel prepared by powder metallurgy contains a large amount of Co element, which can promote the precipitation of secondary carbides. The PM60 high-speed steel was quenched at 1120, 1150, 1180 and 1210 ℃, and oil cooling, and then tempered three times at 540, 560 and 580 ℃. After the heat treatment, the microstructure, precipitated phases, and hardness of the PM60 high speed steel after heat treatment were analyzed by metallographic microscope, scanning electron microscope, and Rockwell hardness tester. The types, morphology, composition, distribution, and precipitation behavior of the carbides in the samples before and after heat treatment were investigated by using JMatPro thermodynamic calculation software. The results show that the original precipitation phases are MC, M₆C, M₂₃C₆and M₇C₃ phases, after heat treatment, the precipitation phases are MC and M₆C phases. By energy spectrum analysis, two types of carbides are found: the dark V-rich carbides, and the bright W and Mo-rich carbides. In the quenching process, part of the carbides is dissolved, and in the tempering process, there is fine dispersive secondary carbides precipitated out. Under the condition of quenching at 1180 ℃+tempering at 540 ℃, the hardness of the tested steel is the highest.

Key words: PM60 high-speed steel, powder metallurgy, carbides, heat treatment, precipitation

中图分类号:

TG161

殷锦华, 祝柏林, 胡木林, 彭会. 热处理对高Co、高V粉末高速钢PM60碳化物析出的影响[J]. 金属热处理, 2024, 49(3): 68-76.

Yin Jinhua, Zhu Bailin, Hu Mulin, Peng Hui. Effect of heat treatment process on carbide precipitation in high Co and high V high-speed steel PM60[J]. Heat Treatment of Metals, 2024, 49(3): 68-76.

参考文献

[1]李亮军, 张家敏, 迟宏宵, 等. Co微合金化对M2高速钢组织和性能的影响[J]. 金属热处理, 2022, 47(1): 73-78.
Li Liangjun, Zhang Jiamin, Chi Hongxiao, et al. Effect of Co microalloying on microstructure and properties of M2 high speed steel[J]. Heat Treatment of Metals, 2022, 47(1): 73-78.
[2]王丽仙, 葛昌纯, 郭双全, 等. 粉末冶金高速钢的发展[J]. 材料导报, 2010, 24(S1): 459-462.
Wang Lixian, Ge Changchun, Guo Shuangquan, et al. Development of powder metallurgy high speed steel[J]. Materials Review, 2010, 24(S1): 459-462.
[3]Chang S H, Huang C L, Huang K T, et al. Improvement of the wear and corrosion behaviors of DLC/oxynitriding duplex-treated PM60 high-speed steel via various power densities of DC-pulsed plasma enhanced CVD[J]. ISIJ International, 2016, 56(12): 2276-2283.
[4]邓玉昆, 陈景榕, 王世章. 高速工具钢[M]. 北京: 冶金工业出版社, 2002.
[5]赵志刚, 仇圣桃, 朱荣. M2钢连铸过程中碳化物析出行为[J]. 材料热处理学报, 2016, 37(7): 214.
Zhao Zhigang, Qiu Shengtao, Zhu Rong, et al. Precipitation behavior of carbides during continuous casting of M2 steel[J]. Transactions of Materials and Heat Treatment, 2016, 37(7): 214.
[6]王启明, 成国光, 黄宇. M2高速钢大尺寸碳化物的形貌特征及析出机理[J]. 钢铁, 2018, 53(1): 65-71.
Wang Qiming, Cheng Guoguang, Huang Yu. Morphology and precipitation mechanism of large carbides in M2 high speed steel[J]. Iron & Steel, 2018, 53(1): 65-71.
[7]刘笑笑, 张铮, 张杰, 等. 回火温度对柔性齿轮钢40CrNiMo组织及力学性能的影响[J]. 金属热处理, 2021, 46(8): 99-104.
Liu Xiaoxiao, Zhang Zheng, Zhang Jie, et al. Effect of tempering temperature on microstructure and mechanical properties of 40CrNiMo steel for flexible gear[J]. Heat Treatment of Metals, 2021, 46(8): 99-104.
[8]Zhou B, Shen Y, Chen J, et al. Evolving mechanism of eutectic carbide in as-cast AISI M2 high-speed steel at elevated temperature[J]. Journal of Shanghai Jiaotong University, 15(4): 463-471.
[9]赵峥嵘, 曹玉龙, 万响亮, 等. W3Mo4Cr5V6高速钢中碳化物的高温转变行为[J]. 武汉科技大学学报, 2022, 45(1): 1-8.
Zhao Zhengrong, Cao Yulong, Wan Xiangliang, et al. High-temperature carbide transformation behavior of W3Mo4Cr5V6 high-speed steel[J]. Journal of Wuhan University of Science and Technology, 2022, 45(1): 1-8.
[10]罗乙娲. M42 高速钢中碳化物的析出机理与转化规律研究[D]. 北京: 北京科技大学, 2019.
Luo Yiwa. Study on precipitation mechanism and transformation law of carbides in M42 high speed steel[D]. Beijing: University of Science and Technology Beijing, 2019.
[11]Luo Y, Guo H, Guo J, etal. Gleeble-simulated and semi-industrial studies on the microstructure evolution of Fc-Co-Cr-Mo-W-V-C alloy during hot deformation[J]. Materials, 2018, 11: 2577.
[12]Xu L, Xing J, Wei S, et al. Optimization of heat treatment technique of high-vanadium high-speed steel based on back-propagation neural networks[J]. Materials and Design, 2007, 28: 1425-1432.
[13]Liu Y, Ning Y, Yao Z K, et al. Hot deformation behavior of the 1.15C-4.00Cr-3.00V-6.00W-5.00Mo powder metallurgy high speed steel[J]. Materials and Design, 2014, 54: 54-63.
[14]Liu H C, Shi W, He Y L, et al. The effect of alloy elements on selective oxidation and galvanizability of TRIP-aided steel[J]. Surface And Interface Analysis, 2010(42): 1685-1689.
[15]文小浩, 陈胜, 丁小芹, 等. SPS烧结M42粉末冶金高速钢的显微组织与性能[J]. 粉末冶金技术, 2010, 28(1): 39-42
Wen Xiaohao, Chen Sheng, Ding Xiaoqin, et al. Microstructure and mechanical properties of PM M42 high speed steel prepared by spark plasma sintering[J]. Powder Metallurgy Technology, 2010, 28(1): 39-42.
[16]迟宏宵, 徐辉霞, 方峰, 等. M2高速钢的高温力学性能[J]. 中国冶金, 2016, 26(1): 31.
Chi Hongxiao, Xu Huixia, Fang Feng, et al. High temperature mechanical properties of M2 high speed steel[J]. China Metallurgy, 2016, 26(1): 31.
[17]Peng H, Hu L, Ngai T, et al. Effects of austenitizing temperature on microstructure and mechanical property of a 4 GPa-grade PM high-speed steel[J]. Materials Science & Engineering A, 2018, 719: 21-26.
[18]谢有, 成国光, 孟晓玲, 等. 含钛H13热作模具钢中大尺寸析出物特征及热稳定性研究[C]//第十届中国钢铁年会暨第六届宝钢学术会议. 上海: 中国金属学会, 2015: 265.
Xie You, Cheng Guoguang, Meng Xiaoling, et al. Large precipitates in titanium-containing H13 tool steel[C]//The 10th China Steel Annual Conference and the 6th Baosteel Academic Conference. Shanghai: The Chinese Society for Metals, 2015: 265.
[19]贾寓真, 吴懿萍, 匡旭光, 等. 传统冶炼高速钢E M42与粉末冶金高速钢ASP2042的回火特性[J]. 金属热处理, 2018, 43(6): 211-216.
Jia Yuzhen, Wu Yiping, Kuang Xuguang, et al. Tempering characteristics of conventional high-speed steel E M42 and powder metallurgical high-speed steel ASP2042[J]. Heat Treatment of Metals, 2018, 43(6): 211-216.

热处理对高Co、高V粉末高速钢PM60碳化物析出的影响

Effect of heat treatment process on carbide precipitation in high Co and high V high-speed steel PM60

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	谢谱, 赵吉庆, 颜廷亭. 回火工艺对HT9钢组织和力学性能的影响[J]. 金属热处理, 2024, 49(3): 44-49.
[2]	吴红庆, 毛宏, 邓志鹏, 宁辉, 吴晓春. SLD-MAGIC冷作模具钢的热处理微畸变特性及其机理[J]. 金属热处理, 2024, 49(3): 128-134.
[3]	汪英芝, 郑留伟, 杨飞, 聂豫晋, 孟立鑫, 尹磊, 梁伟. 选区激光熔化Inconel 718合金的沉淀析出行为及力学性能[J]. 金属热处理, 2024, 49(3): 141-146.
[4]	于林然, 杨卓越, 苏杰, 丁雅莉, 刘赓. 一种新型2 GPa级低合金超高强度钢及热处理工艺[J]. 金属热处理, 2024, 49(3): 164-167.
[5]	郭续龙, 周扬, 陈琦. Inconel718高温合金Laves相及碳化物析出机理[J]. 金属热处理, 2024, 49(3): 190-197.
[6]	刘敏, 郑志鹏, 甘利红, 刘胤辰, 刘震, 张阳, 冯波, 刘春泉. 桁架用Nb-Mo微合金中锰钢强化机理及碳化物析出行为[J]. 金属热处理, 2024, 49(3): 198-203.
[7]	陆凤君. V-N微合金化非调质钢的组织和力学性能[J]. 金属热处理, 2024, 49(3): 204-208.
[8]	裴明德, 李国平, 秦宇航, 张峰, 范新智, 郭宏钢. V含量对不锈钢TDVS2001组织性能的影响[J]. 金属热处理, 2024, 49(3): 251-255.
[9]	刘禹, 孙迎建. 合金元素Si、V、Ti对40Cr13马氏体不锈钢组织与性能的影响[J]. 金属热处理, 2024, 49(3): 256-261.
[10]	董佳欣, 罗云, 蒋文春, 谷文斌, 董丕健. 大型厚壁筒体电磁感应加热均温性控制与参数优化[J]. 金属热处理, 2024, 49(3): 275-278.
[11]	高明昕, 徐林聪, 汪洋, 杨建, 宋华. 钢轨热处理喷风冷却超音速仿形喷嘴设计及仿真[J]. 金属热处理, 2024, 49(3): 286-292.
[12]	张力文, 刘强, 雷超, 沈雪红. 铝锂合金析出强化行为的影响因素及其研究进展[J]. 金属热处理, 2024, 49(3): 313-319.
[13]	谭鑫禹, 刘静静, 刘东雨. Si对Al-1.5Cu-0.7Mg合金组织和性能的影响[J]. 金属热处理, 2024, 49(2): 53-59.
[14]	张乐, 蒋宏利, 谢本昌, 王东梅, 岑耀东, 陈林. 珠光体钢轨钢连续冷却转变曲线测定及组织分析[J]. 金属热处理, 2024, 49(2): 66-70.
[15]	伍伟, 袁清, 莫家璇, 任杰, 张志成, 徐光. 低碳汽车齿轮钢20CrMnTi伪渗碳过程晶粒粗化行为[J]. 金属热处理, 2024, 49(2): 84-90.