配分时间对低碳热轧F-Q&P钢组织和性能的影响

doi:10.13251/j.issn.0254-6051.2022.09.005

金属热处理 ›› 2022, Vol. 47 ›› Issue (9): 27-30.DOI: 10.13251/j.issn.0254-6051.2022.09.005

配分时间对低碳热轧F-Q&P钢组织和性能的影响

苏长珠, 吴润, 李钊, 吴腾, 秦金柱

武汉科技大学材料与冶金学院, 湖北武汉 430081

收稿日期:2022-04-19 修回日期:2022-07-08 发布日期:2022-10-18
通讯作者: 吴润,教授,博士, E-mail:runwu@wust.edu.cn
作者简介:苏长珠(1997—),男,硕士研究生,主要研究方向为高强韧钢铁材料,E-mail:1982536748@qq.com。
基金资助:
省部共建耐火材料与冶金国家重点实验室青年基金(2018QN07)

Effect of partitioning time on microstructure and properties of low carbon hot rolled F-Q&P steel

Su Zhangzhu, Wu Run, Li Zhao, Wu Teng, Qin Jinzhu

School of Materials and Metallurgy, Wuhan University of Science and Technology, Wuhan Hubei 430081, China

Received:2022-04-19 Revised:2022-07-08 Published:2022-10-18

摘要/Abstract

摘要： 采用二辊可逆轧机,研究了弛豫-淬火配分(F-Q&P)工艺中配分时间对试验钢组织及力学性能的影响。研究表明,在弛豫-淬火配分(F-Q&P)工艺下,试验钢的组织主要以多边形铁素体、板条马氏体和残留奥氏体组成;当配分时间延长,试验钢的强度降低,屈强比先降低后升高,伸长率增加,加工硬化指数n值和残留奥氏体含量先增加后下降。进行60 s配分后,试验钢有最低的屈强比和最高的n值,分别为0.62和0.12,抗拉强度和伸长率分别为1090 MPa和19.0%, 力学性能最佳。

关键词: F-Q&P工艺, 配分时间, 多边形铁素体, 残留奥氏体, 形变亚结构

Abstract: Using a two-high reversing mill, effect of partitioning time of the relaxation-quenching partition (F-Q&P) process on microstructure and mechanical properties of tested steel was studied. The results show that under the relaxation-quenching partitioning (F-Q&P) process, the microstructure of the tested steel is mainly composed of polygonal ferrite, lath martensite and retained austenite. When the partitioning time is prolonged, the strength of the tested steel decreases, the yield ratio first decreases and then increases, the elongation increases, and the hardening index n value and the retained austenite content first increase and then decrease. After partitioning for 60 s, the tested steel has the lowest yield ratio and highest n value, 0.62 and 0.12, respectively, and the tensile strength and elongation are 1090 MPa and 19.0%, respectively, the mechanical properties are optimum.

Key words: F-Q&P process, partitioning time, polygonal ferrite, retained austenite, deformation substructure

中图分类号:

TG156

苏长珠, 吴润, 李钊, 吴腾, 秦金柱. 配分时间对低碳热轧F-Q&P钢组织和性能的影响[J]. 金属热处理, 2022, 47(9): 27-30.

Su Zhangzhu, Wu Run, Li Zhao, Wu Teng, Qin Jinzhu. Effect of partitioning time on microstructure and properties of low carbon hot rolled F-Q&P steel[J]. Heat Treatment of Metals, 2022, 47(9): 27-30.

参考文献

[1]Moor E D, Gibbs P J, Speer J G, et al. Strategies for third-generation advanced high-strength steel development[J]. Iron and Steel Technology, 2010, 7(11): 133-144.
[2]朱国明, 康永林, 朱帅. 汽车用超高强QP钢的工艺与组织性能研究[J]. 机械工程学报, 2017, 53(12): 110-117.
Zhu Guoming, Kang Yonglin, Zhu Shuai. Study on process, microstructure and property of ultra-high strength QP steel for automobile[J]. Journal of Mechanical Engineering, 2017, 53(12): 110-117.
[3]Schmitt J H, Lung T. New developments of advanced high-strength steels for automotive applications[J]. Comptes Rendus Physique, 2018, 19(8): 641-656.
[4]汪淼, 张聪, 胡锋, 等. 相变诱导塑性汽车用钢的发展现状与趋势[J]. 钢铁研究学报, 2016, 28(8): 1-7.
Wang Miao, Zhang Cong, Hu Feng, et al. Current status and trend of TRIP automotive steels[J]. Journal of Iron and Steel Research, 2016, 28(8): 1-7.
[5]Speer J G, Matlock D K, Moor D E, et al. Highlights of recent progress in automotive sheet steel development[J]. World Iron Steel, 2013, 13(5): 48-54.
[6]Matlock D K, Speer J G. Third Generation of AHSS: Microstructure Design Concepts[M]. London: Springer, 2009: 185-205.
[7]Speer J G, Matlock D K, De Cooman B C, et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9): 2611-2622.
[8]Matlock D K, Brautigam V E, Speer J G. Application of the quenching and partitioning (Q&P) process to a medium-carbon, high-Si microalloyed bar steel[J]. Materials Science Forum, 2003, 426-432: 1089-1094.
[9]Bagliani E P, Santofimia M J, Zhao L, et al. Microstructure, tensile and toughness properties after quenching and partitioning treatments of a medium-carbon steel[J]. Materials Science and Engineering A, 2013, 559: 486-495.
[10]李辉, 米振莉, 张华, 等. 配分时间对Q&P钢力学性能及显微组织的影响[J]. 材料导报, 2017, 31(4): 83-86, 93.
Li Hui, Mi Zhenli, Zhang Hua, et al. Influence of partition time on mechanical properties and microstructure of Q&P steel[J]. Materials Review, 2017, 31(4): 83-86, 93.
[11]田亚强, 曹仲乾, 潘红波, 等. 两相区温度对中锰钢IQ&P处理后组织和力学性能的影响[J]. 金属热处理, 2020, 45(7): 37-41.
Tian Yaqiang, Cao Zhongqian, Pan Hongbo, et al. Effect of intercritical temperature on microstructure and mechanical properties of medium manganese steel after IQ&P treatment[J]. Heat Treatment of Metals, 2020, 45(7): 37-41.
[12]Rizzo F C, Edmonds D V, He K, et al. Carbon enrichment of austenite and carbide precipitation during the quenching and partitioning (Q&P) process[J]. Solid Phase Transformations in Inorganic Materials, 2005: 535-544.
[13]Zhong N, Wang X D, Wang L, et al. Enhancement of the mechanical properties of a Nb-microalloyed advanced high-strength steel treated by quenching-partitioning-tempering process[J]. Materials Science and Engineering A, 2009, 506(1/2): 111-116.
[14]Zhang J, Ding H, Misra R, et al. Microstructural evolution and consequent strengthening through niobium-microalloying in a low carbon quenched and partitioned steel[J]. Materials Science and Engineering, 2015, 641: 242-248.
[15]尹红霞, 李辉, 史春丽, 等. 奥氏体化温度对汽车用QP钢组织性能的影响[J]. 金属热处理, 2017, 42(11): 108-111.
Yin Hongxia, Li Hui, Shi Chunli, et al. Effect of austenitizing temperature on microstructure and mechanical properties of automotive QP steel[J]. Heat Treatment of Metals, 2017, 42(11): 108-111.
[16]余香芸, 石增敏, 池波, 等. 热成形配分工艺对超高强钢组织和力学性能的影响[J]. 钢铁研究学报, 2015, 27(4): 63-68.
Yu Xiangyun, Shi Zengmin, Chi Bo, et al. Effects of hot formation and partitioning process on microstructure and mechanical properties of ultra-high strength steel[J]. Journal of Iron and Steel Research, 2015, 27(4): 63-68.
[17]徐祖耀. 马氏体相变与马氏体[M]. 2版.北京: 科学出版社, 1999.
[18]王亚婷, 万德成, 冯树明, 等. 淬火温度对中锰QP钢组织和性能的影响[J]. 金属热处理, 2020, 45(5): 172-176.
Wang Yating, Wan Decheng, Feng Shuming, et al. Effect of quenching temperature on microstructure and mechanical properties of medium manganese QP steel[J]. Heat Treatment of Metals, 2020, 45(5): 172-176.

配分时间对低碳热轧F-Q&P钢组织和性能的影响

Effect of partitioning time on microstructure and properties of low carbon hot rolled F-Q&P steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	周丽娜, 刘明, 高翔, 王文雪, 童锐. 奥氏体化过程对Cr14Mo4V高温轴承钢微观组织的影响[J]. 金属热处理, 2022, 47(8): 7-15.
[2]	李慧东, 张覃轶, 刘伟, 孙伟, 伍冬. 深冷处理对440C马氏体不锈钢组织和耐蚀性的影响[J]. 金属热处理, 2022, 47(8): 152-157.
[3]	刘麟, 徐海卫, 李红斌, 韩赟, 田亚强, 郑小平, 陈连生. 两相区连续退火均热温度对Q&P980钢组织性能的影响[J]. 金属热处理, 2022, 47(8): 177-181.
[4]	王思超, 徐海卫, 徐勇, 韩赟, 郑小平, 李红斌, 田亚强, 陈连生. ART退火后冷却方式对0.1C-7.2Mn钢加工硬化行为的影响[J]. 金属热处理, 2022, 47(7): 58-62.
[5]	冯树明, 万德成, 胡进朋, 李杰. 配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 54-58.
[6]	冯继科, 定巍, 李岩, 张光莹, 张楠. 1.5Al中锰钢短时临界退火后的组织与性能[J]. 金属热处理, 2022, 47(5): 136-140.
[7]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[8]	陈连生, 房宁, 曹仲乾, 杨子旋, 李红斌, 潘红波, 田亚强. 压下率对两相区温轧淬火配分中锰钢组织性能的影响[J]. 金属热处理, 2022, 47(3): 28-33.
[9]	刘韬, 吴红艳, 高秀华, 秦岽烊, 杜林秀. 临界区回火温度对Fe-4Mn-1.2Cr-0.3Cu-0.6Ni中锰钢微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(2): 91-98.
[10]	董瑞, 陈林, 岑耀东, 包喜荣. 不同热处理条件下贝氏体钢的微观组织和疲劳裂纹扩展[J]. 金属热处理, 2022, 47(2): 153-158.
[11]	侯雅青, 张宇, 于明光, 王静静, 杨丽, 苏航. Q&P钢残留奥氏体含量的热动力学计算[J]. 金属热处理, 2022, 47(1): 25-31.
[12]	高亚平, 师仲然, 贾涓, 罗小兵, 宋新莉. 热处理工艺对疏浚工程用船体钢组织及磨粒磨损性能的影响[J]. 金属热处理, 2022, 47(1): 32-37.
[13]	邱旭扬帆, 杨卓越, 丁雅莉. 提高Cr-Ni-Mo-Ti马氏体时效不锈钢超低温韧性的固溶处理工艺[J]. 金属热处理, 2022, 47(1): 44-48.
[14]	邓彪, 陈蓬, 王国栋. 回火温度对二次硬化马氏体不锈钢组织和性能的影响[J]. 金属热处理, 2021, 46(9): 65-71.
[15]	赵少甫, 许鸿翔, 王红伟, 郭敬强, 李子岩, 陈岩. 提高20Cr2Ni4A钢齿轮渗碳淬火硬度的试验研究[J]. 金属热处理, 2021, 46(7): 120-125.