配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响

doi:10.13251/j.issn.0254-6051.2022.06.009

金属热处理 ›› 2022, Vol. 47 ›› Issue (6): 54-58.DOI: 10.13251/j.issn.0254-6051.2022.06.009

配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响

冯树明, 万德成, 胡进朋, 李杰

华北理工大学冶金与能源学院, 河北唐山 063210

收稿日期:2022-02-08 修回日期:2022-04-09 出版日期:2022-06-25 发布日期:2022-07-05
通讯作者: 万德成,副教授,博士,E-mail: wandecheng@163.com
作者简介:冯树明(1993—),男,硕士研究生,主要研究方向为QP钢的组织演变与力学性能,E-mail: fengshum@163.com。
基金资助:
河北省科技重大专项(21281008Z);唐山市应用基础研究项目(21130218C)

Effect of partitioning temperature on microstructure and mechanical properties of 0.2C-2.96Mn-1.73Si steel

Feng Shuming, Wan Decheng, Hu Jinpeng, Li Jie

College of Metallurgy and Energy, North China University of Science and Technology, Tangshan Hebei 063210, China

Received:2022-02-08 Revised:2022-04-09 Online:2022-06-25 Published:2022-07-05

摘要/Abstract

摘要： 对0.2C-2.96Mn-1.73Si钢进行IQP(Intercritical heating quenching and partitioning)处理,获得超细化铁素体、马氏体和残留奥氏体多相组织。采用SEM、XRD和拉伸试验机研究了配分温度对试验钢显微组织和力学性能的影响。结果表明,随配分温度的升高,试验钢的抗拉强度逐渐下降,屈服强度和伸长率均先增大后减小。试验钢中残留奥氏体含量随配分温度的升高呈先增加后降低的趋势。配分温度为400 ℃时,残留奥氏体的含量最高,TRIP效应能够提供持久的加工硬化,试验钢获得了最高的均匀变形能力,抗拉强度为1444 MPa,伸长率为20.13%,强塑积达到29 GPa·%,综合力学性能最佳。

关键词: IQP工艺, 配分温度, 残留奥氏体, 力学性能

Abstract: Multiphase structure composed of ultrafine ferrite, martensite and retained austenite was obtained in 0.2C-2.96Mn-1.73Si steel by intercritical heating quenching and partitioning (IQP) heat treatment. The effect of partitioning temperature on microstructure and mechanical properties of the tested steel was researched by means of SEM, XRD and tensile testing machine. The results show that with the increase of partitioning temperature, the tensile strength of the tested steel gradually decreases, and the yield strength and elongation first increase and then decrease. The content of retained austenite in the steel first increases and then decreases with the increase of partitioning temperature. The volume fraction of retained austenite is the highest when the partitioning temperature is 400 ℃, the tested steel has the highest uniform deformability because lasting work hardening can be provided by TRIP effect, and displays excellent comprehensive mechanical properties with ultimate tensile strength of 1444 MPa, elongation of 20.13% and the product of strength and elongation of 29 GPa·%.

Key words: IQP process, partitioning temperature, retained austenite, mechanical properties

中图分类号:

TG142.1

冯树明, 万德成, 胡进朋, 李杰. 配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 54-58.

Feng Shuming, Wan Decheng, Hu Jinpeng, Li Jie. Effect of partitioning temperature on microstructure and mechanical properties of 0.2C-2.96Mn-1.73Si steel[J]. Heat Treatment of Metals, 2022, 47(6): 54-58.

参考文献

[1]Speer J G, Matlock D K, De Cooman B C, et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9): 2611-2622.
[2]Yan S, Liu X, Liu W J, et al. Comparative study on microstructure and mechanical properties of a C-Mn-Si steel treated by quenching and partitioning (Q&P) processes after a full and intercritical austenitization[J]. Materials Science and Engineering A, 2017, 684: 261-269.
[3]Cho L, Seo E J, De Cooman B C. Near-Ac₃ austenitized ultra-fine-grained quenching and partitioning (Q&P) steel[J]. Scripta Materialia, 2016, 123: 69-72.
[4]Zhao Z Z, Liang J H, Zhao A M, et al. Effects of the austenitizing temperature on the mechanical properties of cold-rolled medium-Mn steel system[J]. Journal of Alloys and Compounds, 2017, 691(1): 51-59.
[5]HajyAkbary F, Sietsma J, Miyamoto G, et al. Interaction of carbon partitioning, carbide precipitation and bainite formation during the Q&P process in a low C steel[J]. Acta Materialia, 2016, 104: 72-83.
[6]Santofimia M J, Zhao L, Sietsma J. Microstructural Evolution of a low-carbon steel during application of quenching and partitioning heat treatments after partial austenitization[J]. Metallurgical and Materials Transactions A, 2008, 40: 46-57.
[7]Ayenampudi S, Celada-Casero C, Sietsma J, et al. Microstructure evolution during high-temperature partitioning of a medium-Mn quenching and partitioning steel[J]. Materialia, 2019, 8: 1-11.
[8]詹华, 冷德平, 潘红波, 等. Nb对0.2C-1.5Si-1.8Mn淬火配分钢组织和力学性能的影响[J]. 金属热处理, 2020, 45(3): 73-77.
Zhan Hua, Leng Deping, Pan Hongbo, et al. Influence of Nb on microstructure and mechanical properties of 0.2C-1.5Si-1.8Mn quenching and partitioning steel[J]. Heat Treatment of Metals, 2020, 45(3): 73-77.
[9]Song C, Yu H, Li L, et al. The stability of retained austenite at different locations during straining of I&Q&P steel[J]. Materials Science and Engineering A, 2016, 670: 326-334.
[10]Chen S, Wang G Z, Liu C, et al. Correlation of isothermal bainite transformation and austenite stability in quenching and partitioning steels[J]. Journal of Iron and Steel Research (International), 2017, 24(11): 1095-1103.
[11]Kong H, Chao Q, Cai M H, et al. Microstructure evolution and mechanical behavior of a CMnSiAl TRIP steel subjected to partial austenitization along with quenching and partitioning treatment[J]. Metallurgical and Materials Transactions A, 2018, 49(5): 1509-1519.
[12]Calcagnotto M, Ponge D, Demir E, et al. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual phase steels studied by 2D and 3D EBSD[J]. Materials Science Engineering A, 2010, 527: 2738-2746.
[13]Hu B, Luo H. A novel two-step intercritical annealing process to improve mechanical properties of medium Mn steel[J]. Acta Materialia, 2019, 176: 250-263.
[14]Hu B, Guo H, Misra R D K, et al. Enhanced carbon enrichment in austenite through introducing pre-existing austenite as a ‘carbon container' in 0.2C-2Mn steel: The significant impact on microstructure and mechanical properties[J]. Materials Characterization, 2021, 176: 1-12.
[15]Cai Z H, Ding H, Xue X, et al. Significance of control of austenite stability and three-stage work-hardening behavior of an ultrahigh strength-high ductility combination transformation-induced plasticity steel[J]. Scripta Materialia, 2013, 68: 865-868.
[16]Shi J, Sun X, Wang M, et al. Enhanced work-hardening behavior and mechanical properties in ultrafine-grained steels with large fractioned metastable austenite[J]. Scripta Materialia, 2010, 63: 815-818.
[17]任勇强, 谢振家, 张宏伟, 等. 前躯体组织对C-Mn-Si钢组织特征及力学行为的影响[J]. 金属学报, 2013, 49(12): 1558-1566.
Ren Yongqiang, Xie Zhenjia, Zhang Hongwei, et al. Effect of precursor microstructure on morphology feature and mechanical property of C-Mn-Si steel[J]. Acta Metallurgica Sinica, 2013, 49(12): 1558-1566.
[18]Liu G, Li T, Yang Z G, et al. On the role of chemical heterogeneity in phase transformations and mechanical behavior of flash annealed quenching & partitioning steels[J]. Acta Materialia, 2020, 201: 266-277.

配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响

Effect of partitioning temperature on microstructure and mechanical properties of 0.2C-2.96Mn-1.73Si steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	谷国超, 李瑞芬, 辛振民, 相立新, 许文花, 吕宇鹏. 固溶温度对2507双相不锈钢力学性能及耐蚀性的影响[J]. 金属热处理, 2022, 47(6): 1-6.
[2]	吴杨, 黄晖, 石薇, 文胜平, 吴晓蓝, 荣莉, 魏午. 固溶时效处理对Al-Cu-Mn-Er铸造合金力学性能和显微组织的影响[J]. 金属热处理, 2022, 47(6): 7-12.
[3]	田亚强, 赵志浩, 杨子旋, 徐海卫, 韩赟, 郑小平, 李红斌, 陈连生. 温轧温度对中碳钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 19-24.
[4]	蒋明忠, 赵勇, 潘钱付, 吴裕, 王馨敏, 蒋文龙. F/M钢包壳管材热处理工艺优化[J]. 金属热处理, 2022, 47(6): 25-32.
[5]	翟传田, 孙有平, 何江美, 孟祥超, 万斯雨. 轧制变形量对Mg-Zn-Y合金组织和性能的影响[J]. 金属热处理, 2022, 47(6): 39-45.
[6]	李晓琛, 王世颖, 华天宇, 陈智栋. 深冷处理对TC4钛合金退火过程中微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 46-53.
[7]	白兴红, 赵席春, 赵德利, 王大鹏, 南玉静. 冷却速度对支承辊用Cr5钢显微组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 69-71.
[8]	赵天生, 方羽, 孙誉宾. 成形速度对7050铝合金锻件力学性能和断口形貌的影响[J]. 金属热处理, 2022, 47(6): 103-106.
[9]	舒玮, 王丽英. 固溶处理对奥氏体不锈钢07Cr18Ni11Nb高温力学性能的影响[J]. 金属热处理, 2022, 47(6): 107-110.
[10]	樊开伦, 宋文俊, 戴爱丽, 余传魁, 裴烈勇, 刘勇德, 刘文成. 固溶冷却方式对GH4220合金螺栓力学性能的影响[J]. 金属热处理, 2022, 47(6): 111-114.
[11]	刘少尊, 车洪艳, 李欧, 梁晨, 桂舜, 王铁军. 淬火工艺对粉末冶金马氏体不锈钢组织与性能的影响[J]. 金属热处理, 2022, 47(6): 128-132.
[12]	吕周晋, 李好峰, 车立达, 吴战芳, 翟一多, 崔晓敏, 李向阳. HIP温度对SLM制备TC4钛合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 138-142.
[13]	党玉珍, 蔡晓辉, 陈其源, 刘振宇. 低Ni型LNG钢的热变形行为及力学性能[J]. 金属热处理, 2022, 47(6): 148-154.
[14]	刘帅, 罗贤, 黄斌, 杨延清. 热处理对W芯SiC纤维结构和力学性能的影响[J]. 金属热处理, 2022, 47(5): 7-13.
[15]	郑元凯, 李龙飞, 金康, 李春明, 张文良, 梁君宁. Cu含量对重力铸造Al-Cu-Mg-Sc合金组织及力学性能的影响[J]. 金属热处理, 2022, 47(5): 53-58.