固溶温度对2507双相不锈钢力学性能及耐蚀性的影响

doi:10.13251/j.issn.0254-6051.2022.06.001

金属热处理 ›› 2022, Vol. 47 ›› Issue (6): 1-6.DOI: 10.13251/j.issn.0254-6051.2022.06.001

• 工艺研究 • 下一篇

固溶温度对2507双相不锈钢力学性能及耐蚀性的影响

谷国超^1,2, 李瑞芬³, 辛振民^1,2, 相立新^1,2, 许文花^1,2, 吕宇鹏^1,2

1.山东大学材料液固结构演变与加工教育部重点实验室, 山东济南 250061;
2.山东大学材料科学与工程学院, 山东济南 250061;
3.山东省产品质量检验研究院, 山东济南 250102

收稿日期:2022-01-13 修回日期:2022-03-27 出版日期:2022-06-25 发布日期:2022-07-05
作者简介:谷国超(1982—),男,讲师,博士,主要研究方向为金属热处理,E-mail:guochaogu@sdu.edu.cn
基金资助:
国家重点研发计划(2017YFB 0305101);山东省重大科技创新工程项目(2019JZZY010358,2020CXGC010305,2021ZLGX01)

Effect of solution temperature on mechanical properties and corrosion resistance of super duplex stainless steel 2507

Gu Guochao^1,2, Li Ruifen³, Xin Zhenmin^1,2, Xiang Lixin^1,2, Xu Wenhua^1,2, Lü Yupeng^1,2

1. Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials Ministry of Education, Shandong University, Ji'nan Shandong 250061, China;
2. School of Materials Science and Engineering, Shandong University, Ji'nan Shandong 250061, China;
3. Shandong Institute for Product Quality Inspection, Ji'nan Shandong 250102, China

Received:2022-01-13 Revised:2022-03-27 Online:2022-06-25 Published:2022-07-05

摘要/Abstract

摘要： 利用光学显微镜、扫描电镜、XRD、拉伸试验机和电化学综合测试仪等研究了不同固溶温度对2507超级双相不锈钢组织、力学性能和耐蚀性的影响。采用Thermo-Calc热力学软件计算了2507双相不锈钢的热力学平衡相图,并与测试结果进行了对比。研究结果表明,经1050 ℃及以上温度固溶后,σ相溶解;随着固溶温度的升高,铁素体相含量增加,奥氏体相含量降低,α/γ相体积分数比增加;1050~1100 ℃固溶30 min并水冷时,双相不锈钢具有较好的综合力学性能,屈服强度、抗拉强度和伸长率分别大于600 MPa、840 MPa和35%。1050 ℃固溶30 min时,双相钢可获得较好的耐蚀性能。

关键词: 2507双相不锈钢, 固溶处理, 相比例, 力学性能, 耐蚀性能

Abstract: Effect of solution temperature on microstructure, mechanical properties and corrosion resistance of 2507 super duplex stainless steel was investigated by using optical microscope, scanning electron microscopy, XRD, tensile test and electrochemical analysis. The thermodynamic equilibrium phase diagram of the 2507 duplex stainless steel was calculated by Thermo-Calc thermodynamic software and compared with the test results. The results show that σ phase can be eliminated by solution treatment at temperatures higher than 1050 ℃. With the increase of solution temperature, the content of ferrite phase increases, the content of austenite phase decreases, and the volume fraction ratio of α/γ increases. The duplex stainless steel has better comprehensive mechanical properties after solution treatment at 1050-1100 ℃ for 30 min and water cooling, of which the yield strength, tensile strength and elongation are more than 600 MPa, 840 MPa and 35%, respectively. The duplex stainless steel can obtain better corrosion resistance after solution treatment at 1050 ℃ for 30 min.

Key words: super duplex stainless steel 2507, solution treatment, phase ratio, mechanical properties, corrosion resistance

中图分类号:

谷国超, 李瑞芬, 辛振民, 相立新, 许文花, 吕宇鹏. 固溶温度对2507双相不锈钢力学性能及耐蚀性的影响[J]. 金属热处理, 2022, 47(6): 1-6.

Gu Guochao, Li Ruifen, Xin Zhenmin, Xiang Lixin, Xu Wenhua, Lü Yupeng. Effect of solution temperature on mechanical properties and corrosion resistance of super duplex stainless steel 2507[J]. Heat Treatment of Metals, 2022, 47(6): 1-6.

参考文献

[1]Song Zhigang, Feng Han, Hu Shaomei. Development of Chinese duplex stainless steel in recent years[J]. Journal of Iron and Steel Research, 2017, 24(2): 121-130.
[2]刘振宝, 梁剑雄, 苏杰, 等. 高强度不锈钢的研究及发展现状[J]. 金属学报, 2020, 56(4): 549-557.
Liu Zhenbao, Liang Jianxiong, Su Jie, et al. Research and application progress in ultra-high strength stainless steel[J]. Acta Metallurgica Sinica, 2020, 56(4): 549-557
[3]蔺晓亮, 陈兴润, 王宝君, 等. 固溶温度对S32750双相不锈钢组织和力学性能的影响[J]. 金属热处理, 2019, 44(12): 165-169.
Lin Xiaoliang, Chen Xingrun, Wang Baojun, et al. Effect of solution temperature on microstructure and mechanical properaties of S32750 duplex stainless steel[J]. Heat Treatment of Metals, 2019, 44(12): 165-169.
[4]白青青, 张志宏. 固溶处理温度对2507超级双相不锈钢相比例及力学性能的影响[J]. 金属热处理, 2019, 44(9): 123-127.
Bai Qingqing, Zhang Zhihong. Effect of solution treatment temperature on phase ration and mechanical properties of 2507 super duplex stainless steel[J]. Heat Treatment of Metals, 2019, 44(9): 123-127.
[5]张寿禄, 袁刚, 韩静涛. 超级双相不锈钢00Cr25Ni7Mo4N固溶热处理组织的研究[J]. 物理测试, 2010, 28(3): 9-11.
Zhang Shoulu, Yuan Gang, Han Jingtao. Microstructure of super duplex stainless steel 00Cr25Ni7Mo4N after solution treatment[J]. Physics Examination and Testing, 2010, 28(3): 9-11.
[6]李国平, 李俊, 张威, 等. 固溶温度对超级双相不锈钢S32750板材组织和耐蚀性的影响[J]. 特殊钢, 2009, 30(2): 61-62.
Li Guoping, Li Jun, Zhang Wei, et al. Influence of solution temperature on structure and corrosion resistance of plate of super duplex stainless steel S32750[J]. Special Steel, 2009, 30(2): 61-62.
[7]李俊. 固溶处理对超级双相不锈钢S32750组织和性能的影响[J]. 特殊钢, 2012, 33(4): 64-66.
Li Jun. Effect of solid solution treatment on structure and properties of super duplex stainless steel S32750[J]. Special Steel, 2012, 33(4): 64-66.
[8]郑添义, 陈宁. 冷却速率对2507 SDSS微观组织和力学性能的影响[J]. 船舶工程, 2021, 43(4): 106-112.
Zheng Tianyi, Chen Ning. Effect of cooling rate on microstructure and mechanical properties of 2507 SDSS[J]. Ship Engineering, 2021, 43(4): 106-112.
[9]何婵, 邹德宁, 赵洁, 等. 2507超级双相不锈钢的流变应力本构关系及热加工图[J]. 金属热处理, 2022, 47(1): 94-99.
He Chan, Zou Dening, Zhao Jie, et al. Flow stress constitutive relationship and processing map of super duplex stainless steel 2507[J]. Heat Treatment of Metals, 2022, 47(1): 94-99.
[10]梁丽霞, 赵宏伟, 康喜英, 等. 变形温度对超级双相不锈钢S32750性能的影响[J]. 金属热处理, 2018, 43(9): 191-194.
Liang Lixia, Zhao Hongwei, Kang Xiying, et al. Effect of deformation temperature on properties of super duplex stainless steel S32750[J]. Heat Treatment of Metals, 2018, 43(9): 191-194.
[11]刘富强, 高杰, 叶丙义, 等. 变形量和固溶处理对S32707双相不锈钢组织和性能的影响[J]. 金属热处理, 2017, 42(6): 123-126.
Liu Fuqiang, Gao Jie, Ye Bingyi, et al. Effects of deformation and solution treatment on microstructure and mechanical properties of S32707 duplex stainless steel[J]. Heat Treatment of Metals, 2017, 42(6): 123-126.
[12]Jang Minho, Moon Joonoh, Lee Taeho, et al. Effect of nitrogen partitioning on yield strength in nitrogen-alloyed duplex stainless steel during annealing[J]. Metallurgical and Materials Transactions A, 2014, 45(4): 1653-1658.
[13]高晓丹, 李晶琨, 任学平, 等. 固溶温度对2205双相不锈钢组织和硬度的影响[J]. 金属热处理, 2021, 46(1): 7-10.
Gao Xiaodan, Li Jingkun, Ren Xueping, et al. Effect of solid solution temperature on microstructure and microhardness of 2205 duplex stainless steel[J]. Heat Treatment of Metals, 2021, 46(1): 7-10.
[14]刘爽, 宋志刚, 王曼, 等. 固溶处理温度对超级双相不锈钢UNS S32750的耐点蚀性能与显微组织的影响[J]. 金属热处理, 2018, 43(12): 126-130.
Liu Shuang, Song Zhigang, Wang Man, et al. Effect of solution treatment temperature on pitting corrosion resistance and microstructure of super duplex stainless steel UNS S32750[J]. Heat Treatment of Metals, 2018, 43(12): 126-130.

[1]	吴杨, 黄晖, 石薇, 文胜平, 吴晓蓝, 荣莉, 魏午. 固溶时效处理对Al-Cu-Mn-Er铸造合金力学性能和显微组织的影响[J]. 金属热处理, 2022, 47(6): 7-12.
[2]	田亚强, 赵志浩, 杨子旋, 徐海卫, 韩赟, 郑小平, 李红斌, 陈连生. 温轧温度对中碳钢组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 19-24.
[3]	蒋明忠, 赵勇, 潘钱付, 吴裕, 王馨敏, 蒋文龙. F/M钢包壳管材热处理工艺优化[J]. 金属热处理, 2022, 47(6): 25-32.
[4]	翟传田, 孙有平, 何江美, 孟祥超, 万斯雨. 轧制变形量对Mg-Zn-Y合金组织和性能的影响[J]. 金属热处理, 2022, 47(6): 39-45.
[5]	李晓琛, 王世颖, 华天宇, 陈智栋. 深冷处理对TC4钛合金退火过程中微观组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 46-53.
[6]	冯树明, 万德成, 胡进朋, 李杰. 配分温度对0.2C-2.96Mn-1.73Si钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 54-58.
[7]	陈佳俊, 朱治愿, 李建强, 王守乾. 固溶处理对Cr23Ni7Mo2Cu0.6双相不锈钢组织与性能的影响[J]. 金属热处理, 2022, 47(6): 59-63.
[8]	白兴红, 赵席春, 赵德利, 王大鹏, 南玉静. 冷却速度对支承辊用Cr5钢显微组织与力学性能的影响[J]. 金属热处理, 2022, 47(6): 69-71.
[9]	吴文津, 李相辉, 李雪辰, 陈晶阳, 汤鑫. 固溶处理对K447A高温合金碳化物组织的影响[J]. 金属热处理, 2022, 47(6): 89-92.
[10]	赵天生, 方羽, 孙誉宾. 成形速度对7050铝合金锻件力学性能和断口形貌的影响[J]. 金属热处理, 2022, 47(6): 103-106.
[11]	舒玮, 王丽英. 固溶处理对奥氏体不锈钢07Cr18Ni11Nb高温力学性能的影响[J]. 金属热处理, 2022, 47(6): 107-110.
[12]	樊开伦, 宋文俊, 戴爱丽, 余传魁, 裴烈勇, 刘勇德, 刘文成. 固溶冷却方式对GH4220合金螺栓力学性能的影响[J]. 金属热处理, 2022, 47(6): 111-114.
[13]	刘少尊, 车洪艳, 李欧, 梁晨, 桂舜, 王铁军. 淬火工艺对粉末冶金马氏体不锈钢组织与性能的影响[J]. 金属热处理, 2022, 47(6): 128-132.
[14]	吕周晋, 李好峰, 车立达, 吴战芳, 翟一多, 崔晓敏, 李向阳. HIP温度对SLM制备TC4钛合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(6): 138-142.
[15]	党玉珍, 蔡晓辉, 陈其源, 刘振宇. 低Ni型LNG钢的热变形行为及力学性能[J]. 金属热处理, 2022, 47(6): 148-154.

固溶温度对2507双相不锈钢力学性能及耐蚀性的影响

Effect of solution temperature on mechanical properties and corrosion resistance of super duplex stainless steel 2507

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价