感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响

doi:10.13251/j.issn.0254-6051.2022.08.019

金属热处理 ›› 2022, Vol. 47 ›› Issue (8): 118-122.DOI: 10.13251/j.issn.0254-6051.2022.08.019

感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响

彭龙生¹, 林英华², 黄伟¹, 陈皓²

1.湖南力方轧辊有限公司, 湖南衡阳 421681;
2.南华大学机械工程学院, 湖南衡阳 421001

收稿日期:2022-03-02 修回日期:2022-07-02 出版日期:2022-08-25 发布日期:2022-09-19
作者简介:彭龙生(1962—),男,高级工程师,主要研究方向为高性能轧辊设计与研发,E-mail:lflslfls@163.com。

Effect of induction hardening on hardness and hardened layer depth of Cr12MoV steel roll

Peng Longsheng¹, Lin Yinghua², Huang Wei¹, Chen Hao²

1. Hunan Lifang Roll Co., Ltd., Hengyang Hunan 421681, China;
2. College of Mechanical Engineering, University of South China, Hengyang Hunan 421001, China

Received:2022-03-02 Revised:2022-07-02 Online:2022-08-25 Published:2022-09-19

摘要/Abstract

摘要： 针对Cr12MoV钢轧辊感应淬火易开裂及硬化层深度的问题,研究了预热温度、淬火加热温度、感应圈移动速度和电源频率对Cr12MoV钢轧辊的硬度、开裂和硬化层深度的影响,探索了Cr12MoV钢轧辊具备高硬度不开裂及厚硬化层的方法。结果表明,Cr12MoV钢轧辊调质态硬度低于32 HRC与预热温度高于450 ℃时,能避免淬火开裂;随着感应淬火温度或感应圈移动速度提高,淬火Cr12MoV钢轧辊硬度出现先升高后降低的趋势,但无法明显影响硬化层深度;而随着感应电源频率降低,淬火Cr12MoV钢轧辊硬化层深度明显增加,但对淬火件硬度影响较小。

关键词: Cr12MoV钢轧辊, 感应淬火, 预热温度, 硬度, 硬化层深度

Abstract: In view of the problem of Cr12MoV steel roll cracking easily and hardened layer depth during induction hardening, the effects of preheating temperature, quenching heating temperature, induction coil moving speed and power frequency on hardness, cracking and hardened layer depth of the Cr12MoV steel roll were studied, and the method of Cr12MoV steel roll with high hardness without cracking and thick hardened layer was explored. The results show that when the quenched and tempered hardness of the Cr12MoV steel roll is lower than 32 HRC and the preheating temperature is higher than 450 ℃, quenching cracking can be avoided. With the increase of induction hardening temperature or the moving speed of the induction coil, the hardness of the hardened Cr12MoV steel roll increases first and then decreases, but the hardened layer depth is not significantly affected. However, with the decrease of induction power frequency, the hardened layer depth of hardened Cr12MoV steel roll increases obviously, but it has little effect on hardness of hardened Cr12MoV steel.

Key words: Cr12MoV steel roll, induction hardening, preheating temperature, hardness, hardened layer depth

中图分类号:

TG156.3

彭龙生, 林英华, 黄伟, 陈皓. 感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响[J]. 金属热处理, 2022, 47(8): 118-122.

Peng Longsheng, Lin Yinghua, Huang Wei, Chen Hao. Effect of induction hardening on hardness and hardened layer depth of Cr12MoV steel roll[J]. Heat Treatment of Metals, 2022, 47(8): 118-122.

参考文献

[1]卢军. H13和Cr12MoV钢模具钢的等温淬火[J]. 热处理, 2020, 35(5): 42-45.
Lu Jun. Austempering of H13 and Cr12MoV die steels[J]. Heat Treatment, 2020, 35(5): 42-45.
[2]李涛, 往向杰. Cr12MoV钢模具钢的强韧化热处理工艺研究[J]. 铸造技术, 2018, 39(7): 1565-1567.
Li Tao, Wang Xiangjie. Study on strength-toughening heat treatment process of Cr12MoV die steel[J]. Foundry Technology, 2018, 39(7): 1565-1567.
[3]Pang G X, Li Z L, Chen Z Y. Research on ion nitriding temperature effect on wear resistance of Cr12MoV steel[J]. Physics Procedia, 2013, 50: 120-123.
[4]Wu B Y, Deng L M, Liu P, et al. Effects of picosecond laser repetition rate on ablation of Cr12MoV cold work mold steel[J]. Applied Surface Science, 2017, 409: 403-412.
[5]王卓, 张剑, 尹卫江. Cr12MoV钢冷作模具扁钢轧制弯曲原因分析[J]. 河北冶金, 2020(12): 72-74.
Wang Zhuo, Zhang Jian, Yin Weijiang. Analysis on rolling bending of Cr12MoV cold working die flat steel[J]. Hebei Metallurgy, 2020(12): 72-74.
[6]赵步青, 徐利建, 朱昌宏, 等. Cr12MoV钢的热处理[J]. 热处理, 2021, 36(2): 36-39.
Zhao Buqing, Xu Lijian, Zhu Changhong, et al. Heat treating for Cr12MoV steel[J]. Heat Treatment, 2021, 36(2): 36-39.
[7]马正强, 肖章玉, 刘显有, 等. 热处理工艺对ZG23Cr12MoV钢耐热钢组织与力学性能的影响[J]. 大型铸锻件, 2021(5): 47-49.
Ma Zhengqiang, Xiao Zhangyu, Liu Xianyou, et al. Effect of heat treatment process on microstructure and mechanical properties of ZG23Cr12MoV heat resistant steel[J]. Heavy Casting and Forging, 2021(5): 47-49.
[8]杜思敏, 李雄, 林发驹. 热处理工艺对Cr12MoV钢组织及硬度的影响[J]. 钢铁钒钛, 2021, 42(3): 148-154.
Du Simin, Li Xiong, Lin Faju. Effect of heat treatment process on microstructure and hardness of Cr12MoV steel[J]. Iron Steel Vanadium Titanium, 2021, 42(3): 148-154.
[9]陈枝钧, 彭坤, 许建芳, 等. Cr12MoV钢工作辊感应淬火新工艺[J]. 金属加工(热加工), 2013(S1): 117-119.
Chen Zhijun, Peng Kun, Xu Jianfang, et al. New induction hardening process of Cr12MoV work roll[J]. MW Metal Forming, 2013(S1): 117-119.
[10]程甲兵. Cr12MoV钢材质局部感应加热退火工艺[J]. 金属加工(热加工), 2016(7): 22-24.
Cheng Jiabing. Local induction heating annealing process of Cr12MoV material[J]. MW Metal Forming, 2016(7): 22-24.

[1]	周丽娜, 刘明, 高翔, 王文雪, 童锐. 奥氏体化过程对Cr14Mo4V高温轴承钢微观组织的影响[J]. 金属热处理, 2022, 47(8): 7-15.
[2]	何博, 彭天恩, 胡学文, 蒋波, 郭锐, 石践, 汪飞, 王海波. Nb对高Ti耐候钢连续冷却后显微组织及硬度的影响[J]. 金属热处理, 2022, 47(8): 46-51.
[3]	魏海霞, 潘吉祥, 纪显斌, 李照国, 徐斌. 热处理对经济型高碳马氏体不锈钢J50Cr13组织和硬度的影响[J]. 金属热处理, 2022, 47(8): 148-151.
[4]	石向东, 李德贵, 曹阿林, 古斌, 梁柳青. 热处理温度对Al-Gd合金凝固组织和硬度的影响[J]. 金属热处理, 2022, 47(8): 182-187.
[5]	李向川, 杨吉春, 白国君, 樊志明. 热处理对U76CrRE稀土重轨钢夹杂物和微观组织的影响[J]. 金属热处理, 2022, 47(8): 200-210.
[6]	田春英, 董纪, 王军, 张慧星, 冯天建, 刘晓凡. 淬火温度对5Cr15MoV钢空冷淬火组织与性能的影响[J]. 金属热处理, 2022, 47(8): 211-216.
[7]	朱德荣, 李豪, 柳翊, 王利鸽, 陈智勇, 张慧贤, 梁莉. 固溶时效对SLM成形316L不锈钢块体件显微组织及硬度的影响[J]. 金属热处理, 2022, 47(8): 237-241.
[8]	刘港, 刘静, 杨峰, 向庆. 钛合金化学热处理研究进展[J]. 金属热处理, 2022, 47(8): 249-256.
[9]	魏永强, 顾艳阳, 赵重轻, 蒋志强. 脉冲偏压占空比对TiSiN薄膜结构和性能的影响[J]. 金属热处理, 2022, 47(8): 279-286.
[10]	牛毅, 贺占胥, 王明利, 张杰, 牛文朋, 刘贯军. 离子渗氮对304不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(8): 287-291.
[11]	郑洪, 林文钦, 杨元熙, 徐心洁, 邓枫, 吴佳欣, 蒋洪俊. 30CrMnSiA合金前端吊耳断裂原因分析[J]. 金属热处理, 2022, 47(8): 292-295.
[12]	钟修杨, 邓同生, 朱志云, 李尚, 钟明, 郭涛. 时效处理对稀土钪微合金化钛合金组织与性能的影响[J]. 金属热处理, 2022, 47(7): 40-46.
[13]	索忠源, 杜阳, 付立铭, 单爱党. 配分工艺对5CrMnNiMo超高强度钢摩擦磨损性能的影响[J]. 金属热处理, 2022, 47(7): 134-137.
[14]	蒋文淼, 胡志华, 栾道成, 张旭, 凌俊华, 阴志铭, 李缘, 周新宇, 王正云. 新型贝氏体板簧钢的组织及性能[J]. 金属热处理, 2022, 47(7): 151-155.
[15]	李春辉, 李晓源, 尉文超, 王毛球, 吴润. 冷却速度对超高强马氏体钢的马氏体相变起始温度和硬度的影响[J]. 金属热处理, 2022, 47(7): 183-189.

感应淬火对Cr12MoV钢轧辊硬度和硬化层深度的影响

Effect of induction hardening on hardness and hardened layer depth of Cr12MoV steel roll

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价