渗扩时间比对AISI 316不锈钢渗氮层组织与性能的影响

doi:10.13251/j.issn.0254-6051.2022.05.030

金属热处理 ›› 2022, Vol. 47 ›› Issue (5): 183-188.DOI: 10.13251/j.issn.0254-6051.2022.05.030

渗扩时间比对AISI 316不锈钢渗氮层组织与性能的影响

沈统, 杨丽, 李振, 冯凌宵

沈阳理工大学装备工程学院, 辽宁沈阳 110000

收稿日期:2021-12-20 修回日期:2022-02-26 出版日期:2022-05-25 发布日期:2022-06-16
通讯作者: 杨丽,教授,博士,E-mail: 191553530@qq.com
作者简介:沈统(1996—),男,硕士研究生,主要研究方向为武器装备材料表面改性,E-mail: 714266130@qq.com。
基金资助:
辽宁省高等学校创新人才支持计划 (LR2019060)

Effect of nitriding and diffusion time ratio on microstructure and properties of nitrided layer on AISI 316 stainless steel

Shen Tong, Yang Li, Li Zhen, Feng Lingxiao

School of Equipment Engineering, Shenyang University of Technology, Shenyang Liaoning 110000, China

Received:2021-12-20 Revised:2022-02-26 Online:2022-05-25 Published:2022-06-16

摘要/Abstract

摘要： 采用真空两段渗氮工艺,在不同的强渗、扩散时间下对AISI 316不锈钢进行渗氮处理,通过X射线衍射(XRD)、扫描电镜(SEM)、光学显微镜(OM)、显微硬度测试和摩擦磨损试验等分析了渗氮层的组织和性能。结果表明,经过12 h的真空渗氮后,AISI 316不锈钢表面形成了一层由γ′-Fe₄N、ε-Fe_2-3N和CrN等相组成的渗氮层,其表面硬度和耐磨性能相较于基体均有明显的提高。其中,渗扩时间比为1∶1(强渗6 h、扩散6 h)时的渗层厚度约为96 μm,表面硬度约为1069 HV0.5,是基体表面硬度的4.5倍,在20 N载荷下的磨损量约为基体的1/3;渗扩时间比为1∶2(强渗4 h、扩散8 h)时的渗层厚度约为120 μm,ε-Fe_2-3N相衍射峰增强,在20 N载荷下的磨损量约为基体的1/30。延长扩散时间能增加渗氮层厚度,改善表面形貌,进一步提高不锈钢的耐磨性。

关键词: 真空渗氮, AISI 316不锈钢, 渗扩时间比, 显微组织, 耐磨性能

Abstract: AISI 316 stainless steel was nitrided by two-stage vacuum nitriding process under different strong nitriding and diffusion time. The microstructure and properties of the nitrided layers were analyzed by means of X-ray diffraction (XRD), scanning electron microscope (SEM), optical microscope (OM), microhardness test and friction and wear test. The results show that after vacuum nitriding for 12 h, the nitrided layer consisting of γ′-Fe₄N, ε-Fe_2-3N and CrN phases is formed on the surface of AISI 316 stainless steel. The surface hardness and wear resistance of the nitrided AISI 316 stainless steel are significantly improved compared with those of substrate. Among them, when the nitriding and diffusion time ratio is 1∶1 (strong nitriding for 6 h and diffusion for 6 h), the thickness of the nitrided layer is about 96 μm, the surface hardness is about 1069 HV0.5, which is 4.5 times of the surface hardness of the substrate, and the wear loss under the load of 20 N is about 1/3 of that of the substrate. When the nitriding and diffusion time ratio is 1∶2 (strong nitriding for 4 h and diffusion for 8 h), the nitrided layer thickness is about 120 μm, the diffraction peak of ε-Fe_2-3N phase is enhanced, and the wear loss under the load of 20 N is about 1/30 of that of the substrate. The prolonging of diffusion time can increase the thickness of nitrided layer, improve the surface morphology, and further improve the wear resistance of the AISI 316 stainless steel.

Key words: vacuum nitriding, AISI 316 stainless steel, nitriding and diffusion time ratio, microstructure, wear resistance

中图分类号:

TG156.8

沈统, 杨丽, 李振, 冯凌宵. 渗扩时间比对AISI 316不锈钢渗氮层组织与性能的影响[J]. 金属热处理, 2022, 47(5): 183-188.

Shen Tong, Yang Li, Li Zhen, Feng Lingxiao. Effect of nitriding and diffusion time ratio on microstructure and properties of nitrided layer on AISI 316 stainless steel[J]. Heat Treatment of Metals, 2022, 47(5): 183-188.

参考文献

[1]陈君, 李全安, 张清, 等. AISI 316不锈钢腐蚀磨损交互作用的研究[J]. 中国腐蚀与防护学报, 2014, 34(5): 433-438.
Chen Jun, Li Quanan, Zhang Qing, et al. Sliding wear-corrosion performance of AISI 316 stainless steel against alumina in artificial seawater[J]. Journal of Chinese Society for Corrosion and Protection, 2014, 34(5): 433-438.
[2]Li C X, Bell T. Corrosion properties of plasma nitrided AISI 410 martensitic stainless steel in 3.5% NaCl and 1% HCl aqueous solutions[J]. Corrosion Science, 2005, 48(8): 2036-2049.
[3]葛利玲, 卢正欣, 井晓天, 等. 0Cr18Ni9不锈钢表面纳米化组织及其热稳定性对低温渗氮行为的影响[J]. 金属学报, 2009, 45(5): 566-572.
Ge Liling, Lu Zhengxin, Jing Xiaotian, et al. Effect of surface nanocrystallization and thermal stability of 0Cr19Ni9 stainless steel on low temperature nitriding behavior[J]. Acta Metallurgica Sinica, 2009, 45(5): 566-572.
[4]罗伟, 王均, 闫静, 等. 304奥氏体不锈钢低温盐浴渗氮处理[J]. 材料热处理学报, 2012, 33(10): 107-110.
Luo Wei, Wang Jun, Yan Jing, et al. Low temperature salt bath nitriding of 304 austenitic stainless steel[J]. Transactions of Materials and Heat Treatment, 2012, 33(10): 107-110.
[5]周军, 杨闯, 马亚芹, 等. 真空渗氮时间对TC4钛合金渗氮层组织与性能的影响[J]. 金属热处理, 2018, 43(9): 80-84.
Zhou Jun, Yang Chuang, Ma Yaqin, et al. Influence of vacuum nitriding time on microstructure and properties of nitriding layer of TC4 titanium alloy[J]. Heat Treatment of Metals, 2018, 43(9): 80-84.
[6]韩永珍, 李俏, 徐跃明, 等. 真空低压渗碳技术研究进展[J]. 金属热处理, 2018, 43(10): 253-261.
Han Yongzhen, Li Qiao, Xu Yueming, et al. Research progress of vacuum low pressure carburizing technology[J]. Heat Treatment of Metals, 2018, 43(10): 253-261.
[7]Martinavicˇius A, Abrasonis G, Scheinost A C, et al. Nitrogen interstitial diffusion induced decomposition in AISI 304L austenitic stainless steel[J]. Acta Materialia, 2012, 60(10): 131-136.
[8]Thomas C, Somers M A J. On the crystallographic structure of S-phase[J]. Scripta Materialia, 2003, 50(1): 24-28.
[9]Michal G M, Ernst F, Kahn H, et al. Carbon supersaturation due to paraequilibrium carburization: Stainless steels with greatly improved mechanical properties[J]. Acta Materialia, 2005, 54(6): 159-164.
[10]Mahboubi F, Abdolvahabi K. The effect of temperature on plasma nitriding behaviour of DIN 1.6959 low alloy steel[J]. Vacuum, 2006, 81(3): 239-243.
[11]卢世静, 孙斐, 缪小吉, 等. 离子渗氮和固溶复合处理制备深层含氮奥氏体不锈钢[J]. 表面技术, 2018, 47(10): 180-185.
Lu Shijing, Sun Fei, Miao Xiaoji, et al. Preparation for deep nitriding austenitic stainless steel by complex treatment of plasma nitriding and solid solution[J]. Surface Technology, 2018, 47(10): 180-185.
[12]李广宇, 雷明凯. AISI 316奥氏体不锈钢等离子体源渗氮及其耐磨抗蚀性能[J]. 材料保护, 2017, 50(2): 10-14.
Li Guangyu, Lei Mingkai. Wear and corrosion resistance of AISI 316 austenitic stainless steel after plasma source nitriding treatment[J]. Materials Protection, 2017, 50(2): 10-14.
[13]洪流, 杨闯, 詹永红. 1Cr18Ni9Ti奥氏体不锈钢的真空固溶渗氮处理[J]. 铸造技术, 2016, 37(12): 2563-2565.
Hong Liu, Yang Chuang, Zhan Yonghong. Vacuum solid solution nitriding treatment of 1Cr18Ni9Ti austenitic stainless steel[J]. Foundry Technology, 2016, 37(12): 2563-2565.
[14]禹润缜, 刘胜新, 王朋旭, 等. Fe-Cr-C系硬面合金及其硬质相的研究进展[J]. 材料导报, 2018, 32(21): 3780-3788.
Yu Runzhen, Liu Shengxin, Wang Pengxu, et al. A brief survey on the Fe-Cr-C hard facing alloys and its hard phases[J]. Materials Review, 2018, 32(21): 3780-3788.

[1]	莫金强, 冯光宏, 徐梅, 张威, 李阳. 化学成分对316L奥氏体不锈钢组织及变形行为的影响[J]. 金属热处理, 2022, 47(5): 81-86.
[2]	刘璇, 黄国平, 刘海定, 何曲波, 张楠. 固溶处理对Ni48Cr21Cu2Mo合金组织与力学性能的影响[J]. 金属热处理, 2022, 47(5): 105-110.
[3]	刘丹, 陈杰, 刘文鉴, 周文浩, 罗登, 张青学. 回火温度对Q1100超高强钢组织和性能的影响[J]. 金属热处理, 2022, 47(5): 111-117.
[4]	宿鹏吉, 麻永林, 董丽丽, 温铠, 罗家豪, 刘宝志. 磁场预退火对取向硅钢二次再结晶组织及织构的影响[J]. 金属热处理, 2022, 47(5): 131-135.
[5]	张春雨, 颜瑜, 陈贤帅, 杜如虚. 真空退火处理对选区激光熔化TA2纯钛显微组织及力学性能的影响[J]. 金属热处理, 2022, 47(5): 155-160.
[6]	张明皓, 韩颢源, 徐跃明, 李俏, 高直, 周乐育. 真空渗碳18CrNiMo7-6钢中碳化物的析出规律[J]. 金属热处理, 2022, 47(5): 171-176.
[7]	陈今良, 冯中学, 张利民, 易健宏. 冷轧变形对CrCoNi合金组织与性能的影响[J]. 金属热处理, 2022, 47(5): 204-207.
[8]	陈利超, 王长喜, 苏植成, 王宇宇, 任井涛, 李静, 邓亭, 赵莉萍. 时效工艺对WE43镁合金组织与力学性能的影响[J]. 金属热处理, 2022, 47(5): 208-212.
[9]	李照国, 潘吉祥, 纪显彬, 魏海霞, 王珂. 淬火工艺对6Cr13马氏体不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(5): 226-229.
[10]	张德勇, 冯仰峰, 李维娟, 李伟, 许继勇, 祁敏翔. 终冷温度对Q345R钢组织及性能的影响[J]. 金属热处理, 2022, 47(5): 230-233.
[11]	石如星, 林乙丑, 张沛, 齐国赛, 于文平, 苏文博. 旋回破碎机4Cr13钢主轴套激光淬火后的磨削裂纹分析[J]. 金属热处理, 2022, 47(5): 257-261.
[12]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[13]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[14]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[15]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.

渗扩时间比对AISI 316不锈钢渗氮层组织与性能的影响

Effect of nitriding and diffusion time ratio on microstructure and properties of nitrided layer on AISI 316 stainless steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价