加载应力对铝锂合金蠕变时效行为的影响及本构建模

doi:10.13251/j.issn.0254-6051.2026.02.012

金属热处理 ›› 2026, Vol. 51 ›› Issue (2): 77-81.DOI: 10.13251/j.issn.0254-6051.2026.02.012

加载应力对铝锂合金蠕变时效行为的影响及本构建模

张力文, 边天军, 龚小涛

西安航空职业技术学院, 陕西西安 710089

收稿日期:2025-08-29 修回日期:2025-12-06 发布日期:2026-03-05
作者简介:张力文(1989-),男,副教授,博士,主要研究方向为铝合金蠕变时效成形,E-mail:375350782@qq.com
基金资助:
西安航空职业技术学院2024年度校级重点项目(24XHZD-02);陕西高校青年创新团队“航空关键结构件精确控形控性技术应用创新团队”

Effect of applied stress on creep aging behavior of Al-Li alloy and its constitutive model

Zhang Liwen, Bian Tianjun, Gong Xiaotao

Xi'an Aviation Vocational and Technical College, Xi'an Shaanxi 710089, China

Received:2025-08-29 Revised:2025-12-06 Published:2026-03-05

摘要/Abstract

摘要： 研究了180 ℃下不同加载应力水平对2195铝锂合金的蠕变时效行为,并建立了相应的统一蠕变时效本构模型。结果表明:无论载荷应力如何,蠕变曲线均呈现两阶段特性,且总蠕变应变随着载荷应力的增加而增大;应力越大,相同时效时间下合金的抗拉强度和屈服强度越高,断后伸长率越低。250 MPa下时效合金的屈服强度和抗拉强度比200 MPa时效合金的分别高约17.4%和15.5%,断后伸长率低约27.8%。将试验值与预测值进行对比,发现建立的本构模型能够很好地预测不同加载应力下的蠕变变形和屈服强度,最大相对误差分别为9.5%和8.4%,证明了模型的可靠性。

关键词: 铝锂合金, 蠕变时效, 本构模型

Abstract: Creep aging behavior of 2195 Al-Li alloy under different applied stresses at 180 ℃ was investigated, and a corresponding unified creep aging constitutive model was established. The results indicate that regardless of the applied stress, the creep curves exhibit a two-stage characteristic, and the total creep strain increases with the increase of applied stress. A higher stress leads to higher tensile strength and yield strength, but lower elongation after fracture of the alloy under the same aging time. Compared with the alloy aged at 200 MPa, the yield strength and tensile strength of the alloy aged at 250 MPa are approximately 17.4% and 15.5% higher, respectively, while the elongation after fracture is approximately 27.8% lower. By comparing the measured values with the calculated values, it is found that the established constitutive model can well predict the creep deformation and yield strength under different applied stresses, with the maximum relative errors of 9.5% and 8.4%, respectively, which proves the reliability of the model.

Key words: Al-Li alloy, creep aging, constitutive model

中图分类号:

TG146.2

张力文, 边天军, 龚小涛. 加载应力对铝锂合金蠕变时效行为的影响及本构建模[J]. 金属热处理, 2026, 51(2): 77-81.

Zhang Liwen, Bian Tianjun, Gong Xiaotao. Effect of applied stress on creep aging behavior of Al-Li alloy and its constitutive model[J]. Heat Treatment of Metals, 2026, 51(2): 77-81.

参考文献

[1] 曾元松, 黄遐, 黄硕. 蠕变时效成形技术研究现状与发展趋势[J]. 塑性工程学报, 2008(3): 1-8.
Zeng Yuansong, Huang Xia, Huang Shuo. The research situation and the developing tendency of creep age forming technology[J]. Journal of Plasticity Engineering, 2008(3): 1-8.
[2] 湛利华, 杨有良. 大型构件蠕变时效成形技术研究[J]. 航空制造技术, 2016(13): 16-23.
Zhan Lihua, Yang Youliang. Research on creep age forming technology for large integrated component[J]. Aeronautical Manufacturing Technology, 2016(13): 16-23.
[3] Zhang L W, Li H, Bian T J, et al. Advances and challenges on springback control for creep age forming of aluminum alloy[J]. Chinese Journal of Aeronautics, 2021, 35: 8-34.
[4] Zhan L H, Lin J G, Dean T A. A review of the development of creep age forming: Experimentation, modelling and applications[J]. International Journal of Machine Tools and Manufacture, 2011, 51(1): 1-17.
[5] 李红英, 张建飞, 欧玲, 等. 时效处理对新型Al-Cu-Li合金组织与性能的影响[J]. 金属热处理, 2007, 32(3): 48-52.
Li Hongying, Zhang Jianfei, Ou Ling, et al. Effect of aging process on microstructures and mechanical properties of a new Al-Cu-Li alloy[J]. Heat Treatment of Metals, 2007, 32(3): 48-52.
[6] 张力文, 刘强, 雷超, 等. 铝锂合金析出强化行为的影响因素及其研究进展[J]. 金属热处理, 2024, 49(3): 313-319.
Zhang Liwen, Liu Qiang, Lei Chao, et al. Factors influencing precipitation strengthening behavior of aluminum-lithium alloys and their research progress[J]. Heat Treatment of Metals, 2024, 49(3): 313-319.
[7] Blankenship Jr C P, Starke Jr E A. Structure-property relationships in Al-Li-Cu-Mg-Ag-Zr alloy X2095[J]. Acta Metallurgica et Materialia, 1994, 42(3): 845-855.
[8] Zhang S F, Zeng W D, Yang W H, et al. Ageing response of a Al-Cu-Li 2198 alloy[J]. Materials & Design, 2014, 63: 368-374.
[9] Fu J, Li H, Lei C, et al. Role of thermal-mechanical loading sequence on creep aging behaviors of 5A90 Al-Li alloy[J]. Journal of Materials Processing and Technology, 2018, 255: 354-363.
[10] 董国疆, 孙宇飞, 樊博成, 等. 自然时效对AA7075板材锯齿形屈服行为的影响[J]. 中国有色金属学报, 2021, 31(3): 578-589.
Dong Guojiang, Sun Yufei, Fan Bocheng, et al. Effect of natural aging on Portevin-Le Chatelier effect of AA7075 sheet[J]. The Chinese Journal of Nonferrous Metals, 2021, 31(3): 578-589.
[11] 符师桦, 蔡玉龙, 张青川, 等. 自然时效对 6061 铝合金锯齿形屈服的影响[J]. 稀有金属材料与工程, 2017, 46(12): 3728-3732.
Fu Shihua, Cai Yulong, Zhang Qingchuan, et al. Influence of nature aging on serrated yielding of 6061 Al-based alloy[J]. Rare Metal Materials and Engineering, 2017, 46(12): 3728-3732.
[12] Wu C H, Li H, Bian T J, Natural aging behaviors of Al-Cu-Li alloy: PLC effect, properties and microstructure evolution[J]. Materials Characterization, 2022, 184: 111694.
[13] 于娟, 冯朝辉, 赵唯一, 等. 预拉伸变形量对2050铝锂合金组织和性能的影响[J]. 金属热处理, 2022, 47(6): 64-68.
Yu Juan, Feng Chaohui, Zhao Weiyi, et al. Effect of pre-stretching amount on microstructure and properties of 2050 Al-Li alloy[J]. Heat Treatment of Metals, 2022, 47(6): 64-68.
[14] Agustianingrum M P, Verma S K, Petschke D. Revisiting precipitates in Al-Cu-Li alloys: Experiments and first-principles calculations of thermodynamic stability of Al₂CuLi(T₁) precipitate[J]. Journal of Alloys and Compounds, 2024, 991: 174495.
[15] Lin J G, Ho K C, Dean T A. An integrated process for modelling of precipitation hardening and springback in creep age-forming[J]. International Journal of Machine Tools and Manufacture, 2006, 46(11): 1266-1270.

加载应力对铝锂合金蠕变时效行为的影响及本构建模

Effect of applied stress on creep aging behavior of Al-Li alloy and its constitutive model

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨成, 耿如明, 厉勇, 韩顺, 王春旭. 高韧超高强度DT2200钢的动态力学行为[J]. 金属热处理, 2025, 50(7): 164-173.
[2]	张力文, 刘强, 豆卫涛. 时效温度对2195铝锂合金应力松弛时效行为的影响[J]. 金属热处理, 2025, 50(3): 113-117.
[3]	张力文, 刘强. 预变形对2195铝锂合金应力松弛时效行为的影响[J]. 金属热处理, 2025, 50(2): 160-165.
[4]	宋科锦, 杜玥, 付雪松, 康黎, 杜宝宪, 周文龙. 2195铝锂合金半球壳对流换热系数数值计算及淬火模拟[J]. 金属热处理, 2025, 50(1): 243-249.
[5]	于娟, 冯朝辉, 陈高红, 伍镭. 阳极氧化对酸性盐雾环境中铝锂合金性能的影响[J]. 金属热处理, 2024, 49(7): 281-286.
[6]	孙数理, 侯小虎, 郭文霞, 张静, 王超, 赵学平, 曹宇. 单级固溶温度对喷射沉积2195铝锂合金组织演变的影响[J]. 金属热处理, 2024, 49(6): 62-68.
[7]	李梦琪, 王芝秀, 李海. 时效温度对冷轧2A97铝锂合金拉伸性能和晶间腐蚀敏感性的影响[J]. 金属热处理, 2024, 49(11): 209-214.
[8]	徐桂芳, 宋瑞智, 张杰. 时效处理对喷射成形2195铝锂合金搅拌摩擦焊接头组织与性能的影响[J]. 金属热处理, 2024, 49(10): 78-84.
[9]	段兴旺, 贾悦, 陈迎庆, 车鑫. WE43镁合金的均质化处理及本构模型建立[J]. 金属热处理, 2024, 49(10): 185-190.
[10]	李海涛, 于娟, 刘洪涛, 谢睿勋, 冯朝辉, 赵唯一. 新型高强韧铝锂合金的显微组织和性能[J]. 金属热处理, 2023, 48(4): 173-177.
[11]	贾延祯, 易幼平, 黄始全, 董非, 黄珂. 时效工艺对超低温成形2060铝锂合金组织及性能的影响[J]. 金属热处理, 2023, 48(10): 66-71.
[12]	宗珂朴, 卢雅琳, 王健, 李兴成, 周东帅. Cu含量对铝锂合金组织、力学性能和腐蚀行为的影响[J]. 金属热处理, 2023, 48(10): 207-214.
[13]	顾海, 张捷, 孙健华, 吴国庆, 孙中刚. 激光熔化沉积2195铝锂合金微观组织演变及力学性能[J]. 金属热处理, 2023, 48(1): 52-59.
[14]	郭峰挺, 丛良超, 郭新虎, 杜菲菲, 孙旭东. HST2425钛合金动态力学行为及本构模型[J]. 金属热处理, 2023, 48(1): 87-94.
[15]	王志文, 杨荣东, 黄元春, 李辉. 时效处理对挤压成型2195铝锂合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(9): 6-11.