超超临界锅炉水冷壁T23/12Cr1MoV异种钢焊接接头焊后热处理裂纹分析

doi:10.13251/j.issn.0254-6051.2021.07.042

金属热处理 ›› 2021, Vol. 46 ›› Issue (7): 218-222.DOI: 10.13251/j.issn.0254-6051.2021.07.042

超超临界锅炉水冷壁T23/12Cr1MoV异种钢焊接接头焊后热处理裂纹分析

杨庆旭¹, 王学², 马君鹏¹, 杨超¹

1.江苏方天电力技术有限公司, 江苏南京 211102;
2.武汉大学动力与机械学院, 湖北武汉 430072

收稿日期:2020-10-22 出版日期:2021-07-25 发布日期:2021-12-10
通讯作者: 王学,教授,博士,E-mail:wangxue2011@whu.edu.cn
作者简介:杨庆旭(1978—),男,硕士,主要研究方向为电力金属材料的焊接,E-mail:whuyqx@126.com。
基金资助:
国家自然科学基金面上项目(51574181);四川省科技计划项目(2018JY0668)

Crack analysis of T23/12Cr1MoV dissimilar steel welded joints during PWHT in the water-wall of USC boiler

Yang Qingxu¹, Wang Xue², Ma Junpeng¹, Yang Chao¹

1. Jiangsu Frontier Electric Technology Co., Ltd., Nanjing Jiangsu 211102, China;
2. School of Power and Mechanics, Wuhan University, Wuhan Hubei 430072, China

Received:2020-10-22 Online:2021-07-25 Published:2021-12-10

摘要/Abstract

摘要： 分析了T23/12Cr1MoV异种钢焊接接头焊后热处理裂纹的宏观和微观特征、断口形貌及接头的显微组织,测试了接头的硬度分布,在此基础上讨论了裂纹的性质及形成原因,并提出了防止裂纹的措施。结果表明,裂纹启裂于T23钢侧焊趾部位,沿粗晶粒热影响区(CGHAZ)晶界扩展,为典型的再热裂纹。焊后热处理明显降低了异种钢焊接接头两侧热影响区的硬度,T23钢侧CGHAZ产生再热裂纹与其在焊后热处理过程中晶界析出碳化物有关,其析出促进了孔洞的形成。在焊后热处理前,对异种钢焊接接头进行一次550 ℃×1 h的中间热处理有利于抑制再热裂纹的产生。

关键词: 异种钢焊接接头, 焊后热处理, 裂纹

Abstract: Macro and micro morphologies of cracks occurring in T23/12Cr1MoV dissimilar steel welded joint (DSWJ) during PWHT were analyzed, the microstructure and fracture morphology of the DSWJ were observed, and the hardness distribution across the DSWJ was tested. Based on the experimental results, the types and causes of cracks were discussed, and the measures to prevent cracks were proposed. The results show that the crack initiates at the weld toe of T23 steel side, then propagates along the grain boundaries of its coarse grain heat-affected zone (CGHAZ), which exhibit the characteristics of reheat crack. After PWHT, the hardness of HAZs on both sides of the WM in DSWJ obviously decreases. The formation of reheat crack is related to the precipitation of carbides at grain boundary which promotes the formation of pores in the CGHAZ of T23 steel side during tempering. Before PWHT an intermediate heat treatment performed at 550 ℃ for 1 h is beneficial to suppress reheat crack.

Key words: dissimilar steel welded joint, PWHT, cracks

中图分类号:

TG162.84

杨庆旭, 王学, 马君鹏, 杨超. 超超临界锅炉水冷壁T23/12Cr1MoV异种钢焊接接头焊后热处理裂纹分析[J]. 金属热处理, 2021, 46(7): 218-222.

Yang Qingxu, Wang Xue, Ma Junpeng, Yang Chao. Crack analysis of T23/12Cr1MoV dissimilar steel welded joints during PWHT in the water-wall of USC boiler[J]. Heat Treatment of Metals, 2021, 46(7): 218-222.

参考文献

[1] Bendick W, Gabrel J, Hahn B, et al. New low alloy heat resistant ferritic steels T/P23 and T/P24 for power plant application[J]. International Journal of Pressure Vessels and Piping, 2007, 84(1/2): 13-20.
[2] Arndt J, Haarmann K, Kottmann G, et al. The T23/T24 Book[M]. Germany: V&M, 2000.
[3] Dhooge A, Vekeman J. New generation 2^1/4Cr steels T/P 23 and T/P 24 weldability and high temperature properties[J]. Welding in the World, 2005, 49(9/10): 75-93.
[4] Vaillant J C, Vandenberghe B, Hahn B, et al. T/P23, 24, 911 and 92: New grades for advanced coal-fired power plants—Properties and experience[J]. International Journal of Pressure Vessels and Piping, 2008, 85: 38-46.
[5] 杨富, 章应霖, 任永宁, 等. 新型耐热钢焊接[M]. 北京: 中国电力出版社, 2006: 79.
[6] 王学, 李夕强, 杨超, 等. 超超临界塔式炉T23水冷壁早期失效分析[J]. 中国电力, 2014, 47(12): 21-27.
Wang Xue, Li Xiqiang, Yang Chao, et al. Analysis on early stage failure of welded T23 steel waterwall in USC tower boilers[J]. Electric Power, 2014, 47(12): 21-27.
[7] 王学, 朱迪, 胡磊, 等. 1000 MW塔式炉水冷壁T23钢接头短期失效分析[J]. 中国电机工程学报, 2015, 35(S1): 154-161.
Wang Xue, Zhu Di, Hu Lei, et al. Analysis on short-term failure of T23 steel welded joints in water wall of USC tower boilers[J]. Proceedings of the CSEE, 2015, 35(S1): 154-161.
[8] 王伟, 王学, 钟万里, 等. 屏式过热器T23/12Cr1MoV异种钢接头失效分析[J]. 中国电力, 2013, 46(10): 9-12.
Wang Wei, Wang Xue, Zhong Wanli, et al. Analysis on failure of T23/12Cr1MoV dissimilar steel welded joint in platen superheaters[J]. Electric Power, 2013, 46(10): 9-12.
[9] 王学, 徐德录, 陈玉成, 等. T23钢再热裂纹敏感性[J]. 材料科学与工艺, 2009(S2): 172-175.
Wang Xue, Xu Delu, Chen Yucheng, et al. The reheat cracking susceptibility of T23(7CrWVMoNb9-6) steel[J]. Materials Science and Technology, 2009(S2): 172-175.
[10] 张波, 高子瑜, 王德泰, 等. HCM2S钢再热裂纹敏感性的试验研究[J]. 动力工程, 2006, 26(2): 300-303.
Zhang Bo, Gao Ziyu, Wang Detai, et al. Tests studies on HCM2S steel's susceptibility to reheat cracking[J]. Journal of Power Engineering, 2006, 26(2): 300-303.
[11] Nawrocki J G, Dupont J N, Robino C V, et al. The mechanism of stress-relief cracking in a ferritic alloy steel[J]. Welding Journal, 2003, 82(2): 25-35.
[12] 金玉静, 周巍. 改良型T23钢CGHAZ再热裂纹开裂特征[J]. 金属热处理, 2017, 11(2): 197-203.
Jin Yujing, Zhou Wei. Characteristics of reheat cracking in CGHAZ of modified T23 steel[J]. Heat Treatment of Metals, 2017, 11(2): 197-203.
[13] 张文钺. 焊接冶金学[M]. 北京: 机械工业出版社, 1996: 264.
[14] Li Yong, Wang Xue, Wang Jiaqing, et al. Stress-relief cracking mechanism in simulated coarse-grained heat-affected zone of T23 steel[J]. Journal of Materials Processing Technology, 2019, 266: 73-81.

[1]	杨杰, 汪西, 周杰, 武建祥, 屈志远, 代合平, 彭海军. 转向节锻件枝丫结构淬火裂纹形成机理[J]. 金属热处理, 2022, 47(4): 263-267.
[2]	樊洋, 杨明华, 陈凯敏, 孙丙岩. 焊后热处理对31CrMoV9钢电子束焊接接头组织及性能的影响[J]. 金属热处理, 2022, 47(3): 57-60.
[3]	董瑞, 陈林, 岑耀东, 包喜荣. 不同热处理条件下贝氏体钢的微观组织和疲劳裂纹扩展[J]. 金属热处理, 2022, 47(2): 153-158.
[4]	王春华, 王峰, 王凤良, 房洪杰, 杨丽娟. 多级固溶对7136-0.35La铝合金组织与性能的影响[J]. 金属热处理, 2021, 46(9): 124-128.
[5]	周建波, 张晶, 张蕾涛, 李海涛, 樊帅奇, 徐金富. 激光工艺参数对Ni60/WC涂层裂纹率及组织的影响[J]. 金属热处理, 2021, 46(9): 252-257.
[6]	聂小龙, 高加强, 孟开仁, 王军艺, 刘新宽. 60Si2Mn弹簧钢的断裂失效分析[J]. 金属热处理, 2021, 46(8): 246-249.
[7]	许鸿翔, 王红伟, 张衡, 汪军, 赵少甫. 20Cr2Ni4钢齿轮渗碳淬火及装配后开裂原因分析[J]. 金属热处理, 2021, 46(8): 250-253.
[8]	宋全, 淡婷, 李晓光, 高明森, 曹辉辉. W6Mo5Cr4V2Al高速钢麻花钻断裂原因分析[J]. 金属热处理, 2021, 46(7): 229-232.
[9]	吕晶, 杨其全, 张倩, 胡杰, 许鑫. 铸钢轮装制动盘螺栓孔裂纹产生原因分析[J]. 金属热处理, 2021, 46(7): 238-241.
[10]	吉国强, 葛贵明, 于丽娟, 钟继志. 50CrV4钢垫圈开裂原因分析[J]. 金属热处理, 2021, 46(7): 254-257.
[11]	肖大恒, 张雅静, 何航, 脱臣德, 袁睿, 武会宾. 100 mm厚S420高强钢的热处理工艺及焊接性能[J]. 金属热处理, 2021, 46(6): 107-110.
[12]	张勇路, 鞠泉, 胡曼, 马惠萍, 张世霄. GH3230合金的焊后热处理[J]. 金属热处理, 2021, 46(6): 116-119.
[13]	赵平. 超临界循环流化床锅炉高温过热器管开裂原因分析[J]. 金属热处理, 2021, 46(6): 225-230.
[14]	焦丽, 商海昆, 何剑丰, 赵英军, 张伟民, 李卫民, 周兰梅. 柴油机用42CrMo钢高强度螺栓断裂失效分析[J]. 金属热处理, 2021, 46(6): 245-249.
[15]	米佩, 孙永鹏, 张勇. 矿用齿轨感应淬火裂纹产生原因及改进方法[J]. 金属热处理, 2021, 46(6): 250-252.

超超临界锅炉水冷壁T23/12Cr1MoV异种钢焊接接头焊后热处理裂纹分析

Crack analysis of T23/12Cr1MoV dissimilar steel welded joints during PWHT in the water-wall of USC boiler

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价