0.2C-5Mn-0.5Si-2.5Al中锰钢临界退火后的微观组织及力学性能

doi:10.13251/j.issn.0254-6051.2021.07.007

金属热处理 ›› 2021, Vol. 46 ›› Issue (7): 37-42.DOI: 10.13251/j.issn.0254-6051.2021.07.007

0.2C-5Mn-0.5Si-2.5Al中锰钢临界退火后的微观组织及力学性能

张楠¹, 李岩², 定巍¹

1.内蒙古科技大学材料与冶金学院, 内蒙古包头 014010;
2.内蒙古科技大学内蒙古自治区白云鄂博矿多金属资源综合利用重点实验室, 内蒙古包头 014010

收稿日期:2021-02-26 出版日期:2021-07-25 发布日期:2021-12-10
通讯作者: 定巍,副教授,博士,E-mail:adingwei@126.com
作者简介:张楠(1994—),男,硕士研究生,E-mail:498806131@qq.com。
基金资助:
内蒙古自然科学基金(2019MS05014; 2020LH05026)

Microstructure and mechanical properties of 0.2C-5Mn-0.5Si-2.5Al medium manganese steel after intercritical annealing

Zhang Nan¹, Li Yan², Ding Wei¹

1. School of Materials and Metallurgy, Inner Mongolia University of Science and Technology, Baotou Inner Mongolia 014010, China;
2. Bayan Obo Multimetallic Resource Comprehensive Utilization Key Lab, Inner Mongolia University of Science and Technology, Baotou Inner Mongolia 014010, China

Received:2021-02-26 Online:2021-07-25 Published:2021-12-10

摘要/Abstract

摘要： 利用热力学模拟计算、扫描电镜(SEM)、X射线衍射仪(XRD)、拉伸试验机等设备研究了不同退火工艺下0.2C-5Mn-0.5Si-2.5Al中锰TRIP钢的相变规律、微观组织及力学性能,分析了Al对相变规律及工艺与组织性能的影响规律。结果表明:添加(质量分数)2.5 %Al后,两相区显著扩大,且A₃温度明显提高,这有助于提高临界退火温度,进而加快奥氏体逆相变过程,有效地提高在较短临界时间(1、3 min)退火后的残留奥氏体含量;因2.5 %Al的添加,微观组织中出现了δ-铁素体;在临界退火温度范围内(760~880 ℃),随着退火温度的升高,屈服强度呈现略微下降趋势,而抗拉强度逐渐增加,退火1 min时伸长率及强塑积随退火温度的增加先升高后降低,而退火3 min时伸长率及强塑积随退火温度升高呈持续下降趋势;试样在760 ℃退火3 min可获得最佳的力学性能,抗拉强度为927.69 MPa,伸长率为50.12%,强塑积为46 503.00 MPa·%。

关键词: 中锰TRIP钢, 退火工艺, 相变, 微观组织, 力学性能

Abstract: The phase transformation, microstructure and mechanical properties of the 0.2C-5Mn-0.5Si-2.5Al medium manganese TRIP steel under different annealing processes were studied by means of CALPHAD (calculation of phase diagram) method, SEM (scanning electron microscopy), XRD (X-ray diffractometry) and tensile test. The influence of Al on the law of phase transformation, process, microstructure and properties were studied. The research results show that after the addition of 2.5 %(mass fraction)Al, the two-phase temperature region is significantly expanded, and the A₃ temperature is obviously increased, which is beneficial to increase the intercritical annealing temperature, so the austenite reverse transformation process is accelerated, the retained austenite content after intercritical annealing for short time(1, 3 min) is effectively increased. Due to the addition of 2.5 %Al, δ ferrite appears in the microstructure. In range of 760-880 ℃, with the increase of intercritical annealing temperature, the elongation shows a trend of increasing first and then decreasing, while the yield strength decreases slightly, the tensile strength continues to increase. For 1 min annealing, with the increase of intercritical annealing temperature, the elongation and the product of strength and ductility shows a trend of increasing first and then decreasing. While for 3 min annealing, with the increase of intercritical annealing temperature, the elongation and the product of strength and ductility all show a trend of continue to decrease. The optimum mechanical properties are obtained by annealing at 760 ℃ for 3 min, where the tensile strength is 927.69 MPa, the elongation is 50.12%, and the product of strength and ductility is 46 503.00 MPa·%.

Key words: medium manganese TRIP steel, annealing process, phase transformation, microstructure, mechanical properties

中图分类号:

TG142.1

张楠, 李岩, 定巍. 0.2C-5Mn-0.5Si-2.5Al中锰钢临界退火后的微观组织及力学性能[J]. 金属热处理, 2021, 46(7): 37-42.

Zhang Nan, Li Yan, Ding Wei. Microstructure and mechanical properties of 0.2C-5Mn-0.5Si-2.5Al medium manganese steel after intercritical annealing[J]. Heat Treatment of Metals, 2021, 46(7): 37-42.

参考文献

[1] Zhao J, Jiang Z. Thermomechanical processing of advanced high strength steels[J]. Progress in Materials Science, 2018, 94: 174-242.
[2] Lee S, Estrin Y, Cooman B C. Constitutive modeling of the mechanical properties of V-added medium manganese TRIP steel[J]. Metallurgical and Materials Transactions A, 2013, 44(7): 3136-3146.
[3] Latypov M I, Shin S, Cooman B D, et al. Micromechanical finite element analysis of strain partitioning in multiphase medium manganese TWIP+TRIP steel[J]. Acta Materialia, 2016, 108: 219-228.
[4] Ma Y. Medium-manganese steels processed by austenite-reverted-transformation annealing for automotive applications[J]. Materials Science and Technology, 2017, 33 (15): 1713-1727.
[5] Lee Seawoong, Lee Kyooyoung, De Cooman B C, et al. Observation of the TWIP+TRIP plasticity-enhancement mechanism in Al-added 6 wt pct medium Mn steel[J]. Metallurgical and Materials Transactions A, 2015, 46(6): 2356-2363.
[6] Lee Seawoong, De Cooman B C. On the selection of the optimal intercritical annealing temperature for medium Mn TRIP steel[J]. Metallurgical and Materials Transactions A, 2013, 44: 5018-5024.
[7] Kang S, Hofer R W, Speer J G, et al. Intercritical annealing response of medium manganese steels having different carbon concentrations[J]. Steel Research International, 2018, 89(9).
[8] Hu J, Zhang J M, Sun G S, et al. High strength and ductility combination in nano-/ultrafine-grained medium-Mn steel by tuning the stability of reverted austenite involving intercritical annealing[J]. Springer US, 2019, 54(8).
[9] Li X, Song R, Zhou N,et al. An ultrahigh strength and enhanced ductility cold-rolled medium-Mn steel treated by intercritical annealing[J]. Scripta Materialia, 2018, 154: 30-33.
[10] Chen J, Ren J, Liu Z,et al. 1.0 GPa low carbon medium Mn heavy steel plate with excellent ductility[J]. Materials Science and Technology, 2019, 35(17): 2143-2149.
[11] Nakada N, Mizutani K, Tsuchiyama T, et al. Difference in transformation behavior between ferrite and austenite formations in medium manganese steel[J]. Acta Materialia, 2014, 65: 251-258.
[12] Lee S, Shin S, Kwon M, et al. Tensile properties of medium Mn steel with a bimodal UFG α+γ and coarse δ-ferrite microstructure, Metallurgical and Materials Transactions A, 2017, 48(4): 1678-1700.
[13] Cullity B D, Stock S R. Elements of X-ray diffraction, 3rd edition[J]. Prentice-Hall, 2001.
[14] Moor E D, Matlock D K, Speer J G, et al. Merwin, austenite stabilization through manganese enrichment[J]. Scripta Materialia, 2011, 64(2): 185-188.
[15] Kang S, Speer J G, Krizan D, et al. Prediction of tensile properties of intercritically annealed Al-containing 0.19C-4.5Mn(wt%) TRIP steels[J]. Materials and Design, 2016, 97(2): 138-146.
[16] 王润勋, 王宝峰, 李岩, 等. 0.2C-5Mn-1.5Al中锰TRIP钢的显微组织及力学性能[J]. 金属热处理, 2020, 45(4): 63-68.
Wang Runxun, Wang Baofeng, Li Yan, et al. Microstructure and mechanical properties of 0.2C-5Mn-1.5Al medium manganese TRIP steel[J]. Heat Treatment of Metals, 2020, 45(4): 63-68.
[17] Luo H, Dong H. New ultrahigh-strength Mn-alloyed TRIP steels with improved formability manufactured byintercritical annealing[J]. Materials Science and Engineering A, 2015, 626(12): 207-212.
[18] Zhang Y, Hui W, Zhao X, et al. Effect of reverted austenite fraction on hydrogen embrittlement of TRIP-aided medium Mn steel (0.1C-5Mn)[J]. Engineering Failure Analysis, 2019, 97: 605-616.
[19] 李激光, 隋欣, 张丹, 等. 退火温度对冷轧超细晶亚稳钢组织性能的影响[J]. 材料科学与工程学报, 2015, 33(4): 537-541.
Li Jiguang, Sui Xin, Zhang Dan, et al. Effect of annealing time on microstructure and properties of hot rolled ultrafine grained metastable steel[J]. Journal of Materials Science and Engineering, 2015, 33(4): 537-541.
[20] 定巍, 龚志华, 唐荻, 等. 低硅含铝TRIP钢残余奥氏体变形过程中稳定性研究[J]. 材料工程, 2013 (12): 68-73.
Ding Wei, Gong Zhihua, Tang Di, et al. Stability of retained austenite of low Si containing Al TRIP steel during deformation[J]. Journal of Materials Engineering, 2013(12): 68-73.

0.2C-5Mn-0.5Si-2.5Al中锰钢临界退火后的微观组织及力学性能

Microstructure and mechanical properties of 0.2C-5Mn-0.5Si-2.5Al medium manganese steel after intercritical annealing

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[2]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[3]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[4]	陈东俊, 李广阳, 刘刚. 时效处理对AlSi9Cu3压铸铝合金组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 53-56.
[5]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[6]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[9]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[10]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[11]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[12]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[13]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[14]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[15]	陈强, 陈林芳, 杨明华. 18CrNiMo7-6钢的可控气氛高温渗碳工艺[J]. 金属热处理, 2022, 47(4): 231-239.