复合稀土氧化物对Ti-Al/WC涂层组织和摩擦学性能的影响

doi:10.13251/j.issn.0254-6051.2020.09.039

金属热处理 ›› 2020, Vol. 45 ›› Issue (9): 215-219.DOI: 10.13251/j.issn.0254-6051.2020.09.039

复合稀土氧化物对Ti-Al/WC涂层组织和摩擦学性能的影响

赵运才^1,2, 彭涛¹

1.江西理工大学机电工程学院,江西赣州 341000;
2.河南科技大学高端轴承摩擦学技术与应用国家地方联合工程实验室,河南洛阳 471000

收稿日期:2020-03-26 出版日期:2020-09-25 发布日期:2020-12-29
作者简介:赵运才(1964—),男,教授,博士,主要研究方向为表面工程、再制造工程、摩擦磨损与抗磨技术等,E-mail:zhaoyuncai@126.com
基金资助:
高端轴承摩擦学技术与应用国家地方联合工程实验室开放基金(201713);国家自然科学基金(51565017);江西省自然科学基金(2012BAB206026);江西省教育厅项目(GJJ14424)

Effect of composite rare earth oxides on microstructure and tribological properties of Ti-Al/WC coating

Zhao Yuncai^1,2, Peng Tao¹

1. School of Mechanical and Electrical Engineering,Jiangxi University of Science and Technology,Ganzhou Jiangxi 341000,China;
2. National and Local Joint Engineering Laboratory of High-end Bearing Tribology Technology and Application,Henan University of Science and Technology,Luoyang Henan 471000,China

Received:2020-03-26 Online:2020-09-25 Published:2020-12-29

摘要/Abstract

摘要： 采用等离子喷涂方法制备了未添加稀土氧化物以及含有不同复合稀土氧化物的Ti-Al/WC涂层,使用自带能谱仪的扫描电镜、X射线粉末衍射仪和电子天平对各类涂层的磨损表面及截面组织形貌、残余应力和磨损量进行了观察和检测,使用摩擦磨损试验机比较和分析了不同类型涂层的耐磨性能。结果表明:含有稀土氧化物的Ti-Al/WC涂层内部晶粒得到细化,颗粒物含量大幅度减少,孔洞变小,裂纹数量及尺寸显著降低。与只含一种稀土氧化物的涂层相比,复合稀土氧化物对涂层微观组织改善情况更加明显。当同时加入CeO₂、Y₂O₃和La₂O₃后,涂层组织中的显微缺陷最少,各成分分布最为均匀,截面显微形貌最好,此时,涂层的残余应力达到最小值275.7 MPa,且耐磨性最强,总磨损量仅有16.8 mg。与未添加稀土氧化物的涂层相比,二者分别减少了30.3%和69.8%。

关键词: 复合稀土氧化物, Ti-Al/WC涂层, 组织结构, 残余应力, 耐磨性能

Abstract: Ti-Al/WC coatings of rare earth oxide-free and containing different composite rare earth oxides were prepared by plasma spraying.The worn surface,cross section microstructure,residual stress and wear mass loss of the coatings were observed and detected by using scanning electron microscopy with energy spectrometer,X-ray powder diffractometer and electronic balance.The wear resistance of the coatings was compared and analyzed by using friction and wear tester.The results show that the internal grains of the Ti-Al/WC coating containing rare earth oxide are refined,particulates are greatly reduced,holes are smaller and the number and size of cracks are significantly reduced.Compared with the coating containing only a kind of rare earth oxide,the composite rare earth oxides are more effective in improving microstructure of the coating.When CeO₂,Y₂O₃ and La₂O₃ are all added into the coatings,the defects in microstructure are the least,the components are most evenly distributed,and the cross section morphologies are the best.At the same time,the residual stress of the coating reaches a minimum of 275.7 MPa,the wear resistance is the strongest and the total wear mass loss is only 16.8 mg,compared with the coating of rare earth oxide-free,they are reduced by 30.3% and 69.8% respectively.

Key words: composite rare earth oxides, Ti-Al/WC coating, microstructure, residual stress, wear resistance

中图分类号:

TG174.442

赵运才, 彭涛. 复合稀土氧化物对Ti-Al/WC涂层组织和摩擦学性能的影响[J]. 金属热处理, 2020, 45(9): 215-219.

Zhao Yuncai, Peng Tao. Effect of composite rare earth oxides on microstructure and tribological properties of Ti-Al/WC coating[J]. Heat Treatment of Metals, 2020, 45(9): 215-219.

参考文献

[1] 刘俊.Ni-Al涂层对Ti-Al系金属间化合物抗高温氧化性的影响[D].沈阳:东北大学,2012.
Liu Jun.Effect of Ni-Al coatings on the high-temperature oxidation resistance of Ti-Al based intermetallic compounds[D].Shenyang:Northeastern University,2012.
[2] 王玉玲,张翔宇,孙树峰,等.稀土对激光熔覆3540Fe基合金涂层组织与性能的影响[J].金属热处理,2018,43(3):100-103.
Wang Yuling,Zhang Xiangyu,Sun Shufeng,et al.Effect of rare earth on microstructure and properties of laser cladding 3540Fe-based alloy layer[J].Heat Treatment of Metals,2018,43(3):100-103.
[3] 任现虎.Y对Mo₂FeB₂基金属陶瓷的结构和性能的影响研究[D].天津:天津大学,2017.
Ren Xianhu.The effect of Y addition on the microstructure and mechanical properties of Mo₂FeB₂-based cermets[D].Tianjin:Tianjin University,2017.
[4] Zhan M J,Du X D,Wang F C,et al.Effect of rare earth on microstructure and carbides in WC-Fe composite coating[J].Tribology-Materials,Surfaces and Interfaces,2015,9(3):137-143.
[5] 李俊魁,彭竹琴,马明星,等.CeO₂对AlCoCuFeMnNi高熵合金涂层组织和硬度的影响[J].金属热处理,2017,42(11):19-23.
Li Junkui,Peng Zhuqin,Ma Mingxing,et al.Effect of CeO₂ on microstructure and hardness of AlCoCuFeMnNi high-entropy alloy coating[J].Heat Treatment of Metals,2017,42(11):19-23.
[6] Dhakar B M,Dwivedi D K,Sharma S P.Studies on remelting of tungsten carbide and rare earth modified nickel base alloy composite coating[J].Surface Engineering,2012,28(1):73-80.
[7] Zhang Z,Lu X,Luo J.Tribological properties of rare earth oxide added Cr₃C₂-NiCr coatings[J].Applied Surface Science,2007,253(9):4377-4385.
[8] 邱明,张瑞,李迎春,等.稀土氧化物改性MoS₂基复合涂层的制备及其摩擦学特性研究[J].中国稀土学报,2018,36(2):221-228.
Qiu Ming,Zhang Rui,Li Yingchun,et al.Preparation and tribological properties of MoS₂ based composite coatings modified by rare earth oxide[J].Journal of the Chinese Society of Rare Earths,2018,36(2):221-228.
[9] 谌俊,肖雪军.稀土CeO₂对激光熔覆WC-Co镍基复合涂层组织形貌和性能的影响[J].表面技术,2011,40(6):29-31.
Shen Jun,Xiao Xuejun.Effect of CeO₂ on microstructure and performance of WC-Co Ni-based composite coatings produced by laser cladding[J].Surface Technology,2011,40(6):29-31.
[10] 徐坤山,仇性启,姜辉,等.圆孔缺陷直径与应力集中对金属磁记忆信号的影响[J].磁性材料及器件,2016,47(1):49-53.
Xu Kunshan,Qiu Xingqi,Jiang Hui,et al.Influence of hole diameter and stress concentration on metal magnetic memory signal[J].Journal of Magnetic Materials and Devices,2016,47(1):49-53.
[11] 高万振,刘佐民,高新蕾.表面耐磨损与摩擦学材料设计[M].北京:化学工业出版社,2014.
[12] Wang K L,Zhang Q B,Sun M L,et al.Microstructural characteristics of laser clad coatings with rare earth metal elements[J].Journal of Materials Processing Technology,2003,139(1-3):448-452.

[1]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[2]	朱然, 谢地辉, 朱帅光, 张永康. 高频率Nd∶YLF平顶激光冲击对TC6钛合金表面应力及微变形的影响[J]. 金属热处理, 2022, 47(3): 204-209.
[3]	林基辉, 温亚辉, 范文博, 张腾, 刘晨雨, 薛元琳. 钛合金表面激光改性技术研究进展[J]. 金属热处理, 2022, 47(3): 215-221.
[4]	夏云志, 颜家森, 于兴福, 魏英华, 杨文武, 刘雨健. 基于工作温度8Cr4Mo4V钢制轴承外套圈尺寸及应力变化特征分析[J]. 金属热处理, 2022, 47(3): 245-251.
[5]	师佑杰, 李永刚, 李文辉, 王兴富. 深冷处理对TC4钛合金表面性能的影响[J]. 金属热处理, 2022, 47(2): 183-187.
[6]	张锦刚, 晁利宁, 汪强, 杨晓龙, 周新义, 唐家睿. 消除大型结构件焊接畸变的焊后热处理工艺[J]. 金属热处理, 2022, 47(2): 236-242.
[7]	李礼, 叶宏, 刘越, 佘红艳, 屈威, 沈大臣, 陈梨. Cr12MoV钢表面激光熔覆Ni/Ni-WC梯度涂层的组织与耐磨性能[J]. 金属热处理, 2021, 46(9): 223-228.
[8]	曹晨, 黄春玲, 曹宇鹏, 杨阳, 杨聪. 激光冲击对690高强钢表面完整性的影响[J]. 金属热处理, 2021, 46(9): 247-251.
[9]	叶小飞, 张文, 米艳军, 朱百智, 张玉锁, 易亮, 黄振建. 风电内齿圈感应淬火的数值模拟及验证[J]. 金属热处理, 2021, 46(9): 273-278.
[10]	于春鹏, 王立强, 汤贞涛, 陈丽丽. 铝合金大型锻件淬火过程的有限元模拟[J]. 金属热处理, 2021, 46(9): 279-283.
[11]	李俊衡, 吴运新, 龚海. 胀形对2219铝合金环形件淬火残余应力的影响[J]. 金属热处理, 2021, 46(7): 114-119.
[12]	张勇路, 鞠泉, 胡曼, 马惠萍, 张世霄. GH3230合金的焊后热处理[J]. 金属热处理, 2021, 46(6): 116-119.
[13]	张彝, 谷臻, 高帅龙, 席生岐. 激光熔覆Al_xNbMn₂FeMoTi_0.5高熵合金涂层的组织与性能[J]. 金属热处理, 2021, 46(6): 146-152.
[14]	魏娜莎, 原瑞泽, 牛雪梅, 陈志岗, 陈峙, 闫献国. 深冷处理对35MnB合金钢残余应力的调控机理[J]. 金属热处理, 2021, 46(5): 104-110.
[15]	云璐, 郝新. 退火温度对磁控溅射TiN/TiCN薄膜残余应力、结构及耐蚀性能的影响[J]. 金属热处理, 2021, 46(5): 166-170.

复合稀土氧化物对Ti-Al/WC涂层组织和摩擦学性能的影响

Effect of composite rare earth oxides on microstructure and tribological properties of Ti-Al/WC coating

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价