固溶温度对3D打印TC4钛合金显微组织和力学性能的影响

doi:10.13251/j.issn.0254-6051.2020.11.032

摘要/Abstract

摘要： 对3D打印TC4钛合金进行不同温度固溶+490 ℃时效处理,通过显微组织观察和力学性能试验对其微观组织和力学性能进行了研究。结果表明,3D打印TC4钛合金在原始沉积态时为不均匀的网篮组织,经固溶时效处理后,随着固溶温度的升高,组织中α相先以片状的形式生长于完整的原始晶界附近,再逐渐转变为粗大的板条状,强度逐渐升高而塑性有所降低,当固溶温度为920 ℃时,强度达到最大值,为1100 MPa。当固溶温度超过960 ℃时,α相逐渐被溶解,强度逐渐下降,同时塑性也表现较差。经扫描电镜观察,不同固溶温度下拉伸断口的宏观形貌均呈暗灰色,经890~960 ℃固溶+490 ℃时效处理的TC4钛合金,其微观形貌中存在的大量韧窝,可以判断出其断裂机制为韧性断裂。结合不同固溶时效处理后钛合金的显微组织及力学性能变化可以得出,经920 ℃固溶+490 ℃时效处理后的3D打印TC4钛合金具有较好的综合力学性能。

关键词: 固溶温度, TC4钛合金, 3D打印, 显微组织, 力学性能

Abstract: Microstructure and mechanical properties of TC4 titanium alloy prepared by 3D printing after solution at different temperature and then aging at 490 ℃ were studied through microstructure observation and mechanical property test. The results indicate that the microstructure of the original 3D printed deposition sate is non-uniform basket-weave structure. After solution and aging treatment, with the increase of solution temperature, the α phase first grows in the form of flakes near the complete original grain boundary, and then gradually transforms into a coarse lath shape, and the strength gradually increases while the plasticity decreases, reaching the maximum value of 1100 MPa when solution temperature is 920 ℃. As the solution temperature further increases and exceeds 960 ℃, the α phase is gradually dissolved, which leads to the decrease of the strength and the plasticity. The macro morphologies of the tensile fracture under different solution temperature are all dark gray. According to a large number of dimples observed in the micro morphologies of those fracture, the tensile fracture mechanism of the TC4 titanium alloy can be judged as ductile fracture when solution treated at 890-960 ℃ and aged at 490 ℃. Combining the changes in the microstructure and mechanical properties of the TC4 titanium alloy after different solution and aging treatments, it can be concluded that the TC4 titanium alloy prepared by 3D printing has better comprehensive mechanical properties when solution treated at 920 ℃ and then aged at 490 ℃.

Key words: solution temperature, TC4 titanium alloy, 3D printing, microstructure, mechanical properties

中图分类号:

TG146

鲁媛媛, 张怡, 郭帅, 刘伟锋. 固溶温度对3D打印TC4钛合金显微组织和力学性能的影响[J]. 金属热处理, 2020, 45(11): 171-176.

Lu Yuanyuan, Zhang Yi, Guo Shuai, Liu Weifeng. Influence of solution treatment temperature on microstructure and mechanical properties of TC4 titanium alloy prepared by 3D printing[J]. Heat Treatment of Metals, 2020, 45(11): 171-176.

参考文献

[1]金和喜, 魏克湘, 李建明, 等. 航空用钛合金研究进展[J]. 中国有色金属学报, 2015, 25(2): 280-292.
Jin Hexi, Wei Kexiang, Li Jianming, et al. Research development of titanium alloy in aerospace industry[J]. The Chinese Journal of Nonferrous Metals, 2015, 25(2): 280-292.
[2]王清江, 刘建荣, 杨锐. 高温钛合金的现状与前景[J]. 航空材料学报, 2014, 34(4): 1-26.
Wang Qingjiang, Liu Jianrong, Yang Rui. High temperature titanium alloys: Status and perspective[J]. Journal of Aeronautical Materials, 2014, 34(4): 1-26.
[3]赵永庆. 国内外钛合金研究的发展现状及趋势[J]. 中国材料进展, 2010, 29(5): 1-8.
Zhao Yongqing. Current situation and development trend of titanium alloys[J]. Materials China, 2010, 29(5): 1-8.
[4]Bache M R. A review of dwell sensitive fatigue in titanium alloys: The role of microstructure, texture and operating conditions[J]. International Journal of Fatigue, 2003, 25(9): 1079-1087.
[5]黄森森, 马英杰, 张仕林, 等. α+β两相钛合金元素再分配行为及其对显微组织和力学性能的影响[J]. 金属学报, 2019, 55(6): 741-750.
Huang Sensen, Ma Yingjie, Zhang Shilin, et al. Influence of alloying elements partitioning behaviors on the microstructure and mechanical properties in α+β titanium alloy[J]. Acta Metallurgica Sinica, 2019, 55(6): 741-750.
[6]刘莹, 曲周德, 王本贤. 钛合金TC4的研究开发与应用[J]. 兵器材料科学与工程, 2005, 28(1): 47-50.
Liu Ying, Qu Zhoude, Wang Benxian. Research development and application of Ti6A14V alloy[J]. Ordnance Material Science and Engineering, 2005, 28(1): 47-50.
[7]肖虎, 李亮. TC4钛合金在低温CO₂冷却下的切削性能[J]. 中国机械工程, 2017, 28(8): 883-887.
Xiao Hu, Li Liang. High speed cutting of TC4 titanium alloy under cryogenic CO₂ cooling conditions[J]. China Mechanical Engineering, 2017, 28(8): 883-887.
[8]马付建, 栾诗宇, 罗奇超, 等. 超声辅助磁性磨料光整加工工艺对钛合金表面完整性的影响[J]. 中国表面工程, 2019, 32(2): 128-136.
Ma Fujian, Luan Shiyu, Luo Qichao, et al. Effects of ultrasonic assisted magnetic abrasive finishing on surface integrity of titanium alloy[J]. China Surface Engineering, 2019, 32(2): 128-136.
[9]刘帅, 王阳, 刘常升. 激光熔化沉积技术在制备梯度功能材料中的应用[J]. 航空制造技术, 2018, 61(17): 47-56.
Liu Shuai, Wang Yang, Liu Changsheng. Application of laser melting deposition technique in preparation of functionally gradient materials[J]. Aeronautical Manufacturing Technology, 2018, 61(17): 47-56.
[10]汤慧萍, 王建, 逯圣路, 等. 电子束选区熔化成形技术研究进展[J]. 中国材料进展, 2015, 34(3): 225-235.
Tang Huiping, Wang Jian, Lu Shenglu, et al. Research progress in selective electron beam melting[J]. Materials China, 2015, 34(3): 225-235.
[11]邓贤辉, 杨治军. 钛合金增材制造技术研究现状及展望[J]. 材料开发与应用, 2014, 29(5): 113-120.
Deng Xianhui, Yang Zhijun. Current situation and prospect of titanium alloy additive manufacturing technology[J]. Development and Application of Materials, 2014, 29(5): 113-120.
[12]李权, 王福德, 王国庆, 等. 航空航天轻质金属材料电弧熔丝增材制造技术[J]. 航空制造技术, 2018, 61(3): 74-82.
Li Quan, Wang Fude, Wang Guoqing, et al. Wire and arc additive manufacturing of lightweight metal components in aeronautics and astronautics[J]. Aeronautical Manufacturing Technology, 2018, 61(3): 74-82.
[13]李明东. 激光沉积制造TC4钛合金的热处理工艺研究[D]. 沈阳: 沈阳航空航天大学, 2018.
Li Mingdong. Study on heat treatment process of TC4 titanium alloy by laser deposition manufacturing[D]. Shenyang: Shenyang Aerospace University, 2018.
[14]Vrancken B, Thijs L, Kruth J P, et al. Heat treatment of Ti6Al4V produced by selective laser melting: Microstructure and mechanical properties[J]. Journal of Alloys and Compounds, 2012, 541(7): 177-185.
[15]李明, 刘洋, 徐怀忠, 等. 固溶处理温度对激光选区熔化成型Ti-6Al-4V钛合金摩擦磨损性能的影响[J]. 材料热处理学报, 2019, 40(8): 39-49.
Li Ming, Liu Yang, Xu Huaizhong, et al. Effect of solid solution treatment temperature on friction and wear properties of Ti-6Al-4V titanium alloy prepared by selective laser melting[J]. Transactions of Materials and Heat Treatment, 2019, 40(8): 39-49.
[16]何伟, 杜小平, 马红征, 等. TC4钛合金相变温度的测定与分析[J]. 理化检验-物理分册, 2014, 50(7): 461-464.
He Wei, Du Xiaoping, Ma Hongzheng, et al. Measurement and analysis of phase transformation temperature of TC4 titanium alloy[J]. Physical Testing and Chemical Analysis(Part A: Physical Testing), 2014, 50(7): 461-464.