奥氏体化温度和冷却速率对含Nb高碳钢组织性能的影响

doi:10.13251/j.issn.0254-6051.2020.06.001

金属热处理 ›› 2020, Vol. 45 ›› Issue (6): 1-6.DOI: 10.13251/j.issn.0254-6051.2020.06.001

• 工艺研究 • 下一篇

奥氏体化温度和冷却速率对含Nb高碳钢组织性能的影响

笪光杰^1,2, 杨忠民², 王凯², 陈颖², 王慧敏², 李少华^2,3

1. 北京科技大学钢铁共性技术协同创新中心, 北京 100083;
2. 钢铁研究总院工程用钢研究所, 北京 100081;
3. 北京科技大学材料科学与工程学院, 北京 100083

收稿日期:2019-12-12 出版日期:2020-06-25 发布日期:2020-09-02
通讯作者: 杨忠民,教授级高级工程师,博士,E-mail:yangzm2005@126.com
作者简介:笪光杰(1993—),男,博士研究生,主要研究方向为钢铁材料组织性能,E-mail:767629474@qq.com。
基金资助:
国家重点研发计划(2017YFB0304800,2017YFB0304802)

Effects of austenitizing temperature and cooling rate on microstructure and properties of Nb-containing high carbon steel

Da Guangjie^1,2, Yang Zhongmin², Wang Kai², Chen Ying², Wang Huimin², Li Shaohua^2,3

1. Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083, China;
2. Institute for Structure Steel, Central Iron and Steel Research Institute, Beijing 100081, China;
3. School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China

Received:2019-12-12 Online:2020-06-25 Published:2020-09-02

摘要/Abstract

摘要： 通过Gleeble 1500型热模拟试验机对含Nb高碳试验钢进行了不同奥氏体化温度和冷速下的热处理。采用光学显微镜、扫描电镜、硬度测量等试验手段对试验钢的显微组织、硬度和珠光体片层间距进行了观察和测量。结果表明:奥氏体化温度为950 ℃时,试验钢淬火后晶粒尺寸为34 μm,硬度为813 HV5,以0.1~5 ℃/s冷速冷却至室温的组织为珠光体+铁素体;而奥氏体化温度为1200 ℃时,淬火后晶粒尺寸为134 μm,硬度为827 HV5,以0.1~1 ℃/s冷速冷却至室温的组织为珠光体+铁素体,冷速为5 ℃/s时,组织为针状马氏体+少量的铁素体。在1220 ℃以上Nb全部固溶在奥氏体中,奥氏体化温度过高会导致晶粒过分长大。珠光体片层间距随着奥氏体化温度的升高和冷却速率的提升而变小,片层间距的减小可使硬度值提高。

关键词: 含Nb高碳钢, 奥氏体化温度, 冷速, 硬度, 珠光体片层间距

Abstract: Heat treatment of a Nb-containing high carbon steel at different austenitizing temperatures and cooling rates was carried out by Gleeble 1500 thermal simulation test machine. The microstructure, hardness and pearlite lamellar spacing of the tested steel were observed and measured by means of metallographic microscope, scanning electron microscope and hardness tester. The results show that when the austenitizing temperature is 950 ℃, the grain size of the tested steel after quenching is 34 μm, the hardness is 813 HV5, and the microstructure cooled to room temperature with cooling rate of 0.1-5 ℃/s is pearlite+ferrite. When the austenitizing temperature is 1200 ℃, the grain size after quenching is 134 μm, the hardness is 827 HV5, and the microstructure cooled to room temperature with cooling rate of 0.1-1 ℃/s is pearlite + ferrite, while that with 5 ℃/s cooling rate is acicular martensite+a small amount of ferrite. Above 1220 ℃, all Nb is completely dissolved in austenite, and too high austenitizing temperature will result in too much grain growth. The pearlite lamellar spacing becomes smaller as the austenitizing temperature increases and the cooling rate increases, and the decrease in the lamellar spacing can increase the hardness value.

Key words: Nb-containing high carbon steel, austenitizing temperature, cooling rate, hardness, pearlite lamellar spacing

中图分类号:

TG142

笪光杰, 杨忠民, 王凯, 陈颖, 王慧敏, 李少华. 奥氏体化温度和冷却速率对含Nb高碳钢组织性能的影响[J]. 金属热处理, 2020, 45(6): 1-6.

Da Guangjie, Yang Zhongmin, Wang Kai, Chen Ying, Wang Huimin, Li Shaohua. Effects of austenitizing temperature and cooling rate on microstructure and properties of Nb-containing high carbon steel[J]. Heat Treatment of Metals, 2020, 45(6): 1-6.

参考文献

[1]曹建春, 雍岐龙, 刘清友, 等. 含铌钼钢中微合金碳氮化物沉淀析出及其强化机制[J]. 材料热处理学报, 2006, 27(5): 51-55.
Cao Jianchun, Yong Qilong, Liu Qingyou, et al. Precipitation of microalloyed carbonitride and its strengthening mechanism in low carbon steels containing Nb and Mo[J]. Transaction of Materials and Heat Treatment, 2006, 27(5): 51-55.
[2]薛春芳, 胡贻苏. 含铌微合金钢中铌的析出行为对晶粒细化的影响[J]. 冶金丛刊, 2004(4): 1-3.
Xue Chunfang, Hu Yisu. Effect of Nb precipitation on the grain fining in Nb-microalloyed steel[J]. Metallurgical Collections, 2004(4): 1-3.
[3]高丽. 铌在钢中的结构及铌对钢性能影响的第一性原理计算[D]. 包头: 内蒙古科技大学, 2013.
Gao Li. First-principles calculations of the structure of niobium in steel and its effect on steel properties[D]. Baotou: Inner Mongolia University of Science and Technology, 2013.
[4]肖振宇. 含铌微合金高强钢力学性能波动成因分析[D]. 上海: 上海交通大学, 2009.
Xiao Zhenyu. Analysis on the causes of mechanical properties fluctuation of niobium-containing microalloyed high-strength steels[D]. Shanghai: Shanghai Jiaotong University, 2009.
[5]刘振成, 张利光, 李斌. 微合金元素对高碳钢盘条组织性能的影响[J]. 炼钢, 2008, 24(6): 50-52.
Liu Zhencheng, Zhang Liguang, Li Bin. Effect of micro-alloyed element on microstructure and property of high carbon steel wire rod[J]. Steelmaking, 2008, 24 (6): 50-52.
[6]金桂香, 王福明, 李克非, 等. 82B高碳钢奥氏体晶粒长大行为[J]. 材料热处理学报, 2013, 34(7): 41-46.
Jin Guixiang, Wang Fuming, Li Kefei, et al. Austenite grain growth behavior of a 82B high carbon steel[J]. Journal of Materials and Heat Treatment, 2013, 34 (7): 41-46.
[7]支萌. X80大变形管线钢组织调控与性能的研究[D]. 秦皇岛: 燕山大学, 2015.
Zhi Meng. Study on microstructure regulation and properties of X80 large deformed pipeline steel[D]. Qinhuangdao: Yanshan University, 2015.
[8]郭海滨, 左秀荣, 张新理, 等. X80M管线钢奥氏体晶粒粗化及Nb/Ti的固溶析出行为[J]. 热加工工艺, 2016, 45(10): 1-5.
Guo Haibin, Zuo Xiurong, Zhang Xinli, et al. Austenite grain coarsening and Nb/Ti solution precipitation behavior of X80M pipeline steel[J]. Hot Working Technology, 2016, 45(10): 1-5.
[9]雍岐龙. 钢铁中的第二相[M]. 北京: 冶金工业出版社, 2006
[10]李麟, 许珞萍. 钢中铌钒碳氮化合物的析出及其稳定性分析[J]. 上海金属, 2005, 27(2): 1-3.
Li Lin, Xu Luoping. Precipitation of carbonitrides containing V and Nb in steel and their stability[J]. Shanghai Metals, 2005, 27(2): 1-3.
[11]杨超飞, 吴庆辉, 陈颖, 等. Nb含量对高碳钢组织和性能的影响[J]. 热加工工艺, 2012, 41(10): 63-66.
Yang Chaofei, Wu Qinghui, Chen Ying, et al. Effect of Nb content on microstructure and properties of high carbon steel[J]. Hot Working Technology, 2012, 41(10): 63-66.
[12]翁宇庆, 孔令航, 王国栋, 等. 超细晶钢——钢的组织细化理论与控制技术[M]. 北京: 冶金工业出版社, 2003.
[13]蔡爱国. 铌钒微合金中碳钢的微观组织与强度的关系[J]. 钢铁研究学报, 1996, 8(2): 35-39.
Cai Aiguo. Microstructure-strength relationships in Nb-V microalloyed medium carbon steel[J]. Journal of Iron and Steel Research, 1996, 8(2): 35-39.
[14]Marder A R, Bramfitt B L. The effect of morphology on the strength of pearlite[J]. Metallurgical Transactions A, 1976, 7(3): 365-372.
[15]杨超飞, 吴庆辉, 陈颖, 等. 铌对高碳钢连续冷却过程中相变和珠光体片层间距的影响[J]. 机械工程材料, 2013, 37(30): 16-20.
Yang Chaofei, Wu Qinghui, Chen Ying, et al. Effect of niobium on phase transition and lamellar spacing of pearlites of high carbon steel during continuous cooling[J]. Materials for Mechanical Engineering, 2013, 37(30): 16-20.
[16]沈奎, 于学森, 廖舒纶, 等. 铌对微合金化高碳钢奥氏体晶粒长大的影响[J]. 材料热处理学报, 2015, 36(2): 102-107.
Shen Kui, Yu Xuesen, Liao Shulun, et al. Effect of Nb on austenite grain growth behavior of V and Nb-V microalloyed high-carbon steels[J]. Journal of Materials and Heat Treatment, 2015, 36(2): 102-107.
[17]程四华, 周德, 孔祥涛, 等. Nb微合金化对高碳钢奥氏体晶粒生长的影响[J]. 金属热处理, 2014, 39(5): 54-57.
Cheng Sihua, Zhou De, Kong Xiangtao, et al. Effect of Nb microalloying on austenite grain growth of high carbon steel[J]. Heat Treatment of Metals, 2014, 39(5): 54-57.
[18]Gladman T, McIvor I, Pickering F. Some aspects of the structure-property relationships in high-C ferrite-pearlite steels[J]. Journal Iron Steel Inst, 1972, 210: 916-930.
[19]Mondal D P, Ray K K, Das S. The strength of ferrite in annealed Armco iron and hypoeutectoid steels[J]. Zeitschrift für Metallkunde, 1998, 89(9): 635-641.
[20]Hyzak J M, Bernstein I M. The role of microstructure on the strength and toughness of fully pearlitic steels[J]. Metallurgical Transactions A, 1976(7): 1217-1224.
[21]左越, 周世同, 李昭东, 等. V和Si对珠光体车轮钢显微组织和力学性能的影响规律[J]. 材料研究学报, 2016, 30(6): 401-408.
Zuo Yue, Zhou Shitong, Li Zhaodong, et al. Effects of V and Si on the microstructure and mechanical properties of medium-carbon pearlitic steels for wheel[J]. Chinese Journal of Materials Research, 2016, 30(6): 401-408.
[22]杨超飞. Nb及热形变对高碳钢连续冷却时组织转变的影响[D]. 北京: 钢铁研究总院, 2012.
Yang Chaofei. Effect of Nb and thermal deformation on microstructure transformation of high carbon steel during continuous cooling[D]. Beijing: Central Iron and Steel Research Institute, 2012.

奥氏体化温度和冷却速率对含Nb高碳钢组织性能的影响

Effects of austenitizing temperature and cooling rate on microstructure and properties of Nb-containing high carbon steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[2]	付锡彬, 陈子豪, 张可, 赵时雨, 孙新军, 朱正海, 梁小凯, 雍岐龙. 淬火温度对高Ti低合金耐磨钢组织及力学性能的影响[J]. 金属热处理, 2022, 47(4): 122-127.
[3]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[4]	孙凯, 陈研, 杨绍斌. 时效温度对激光选区熔化TC21钛合金微观组织及硬度的影响[J]. 金属热处理, 2022, 47(4): 155-158.
[5]	章军, 赵四新. 冷锻齿轮用16MnCrS5钢的球化退火工艺[J]. 金属热处理, 2022, 47(4): 185-188.
[6]	戴建科, 韩顺, 厉勇, 刘宪民, 王春旭, 庞学东, 李建新. 航空齿轮钢C69高温渗碳后的组织性能[J]. 金属热处理, 2022, 47(4): 219-225.
[7]	苏勇, 王帅, 王吉星, 于兴福, 刘洪秀, 刘金玲. 复合化学热处理对G13Cr4Mo4Ni4V钢组织和硬度的影响[J]. 金属热处理, 2022, 47(4): 226-230.
[8]	王敬元, 吴松全, 张博华, 辛社伟, 杨义, 王皞, 黄爱军. 固溶时效处理对BT25y钛合金显微组织及硬度的影响[J]. 金属热处理, 2022, 47(3): 14-19.
[9]	孙建, 黄贞益, 李景辉, 王萍. 固溶和时效处理对Fe-Mn-Al-C轻质钢组织和硬度的影响[J]. 金属热处理, 2022, 47(3): 34-38.
[10]	杨春苗, 王珊, 王淑慧, 李延珍, 刘文文. RRA过程中预时效时间对7A85铝合金组织性能的影响[J]. 金属热处理, 2022, 47(3): 44-47.
[11]	孙国进, 郜志文, 崔效炎, 郜可坤, 孙力. 双液淬火对9Cr2Mo钢辊皮组织与硬度的影响[J]. 金属热处理, 2022, 47(3): 88-91.
[12]	程体娟, 甘斌, 于鸿垚, 周海晶, 郭彩玉, 毕中南, 杜金辉. 固溶处理对新型镍基高温合金组织及性能的影响[J]. 金属热处理, 2022, 47(3): 107-112.
[13]	王荣, 龚玉辉, 殷学俊, 魏德强. 多道电子束扫描搭接率对40Cr钢组织与性能的影响[J]. 金属热处理, 2022, 47(3): 191-197.
[14]	周钟平, 张小娟, 白鹭, 余方印, 闵永安. T250钢离子渗氮后的组织和性能[J]. 金属热处理, 2022, 47(3): 210-214.
[15]	张世进, 李凯, 易丹青, 刘会群. 冷轧TA5钛合金退火过程的再结晶行为及织构演变[J]. 金属热处理, 2022, 47(2): 1-8.