激光功率对40CrNiMoA钢表面淬火组织和摩擦磨损性能的影响

doi:10.13251/j.issn.0254-6051.2020.03.025

金属热处理 ›› 2020, Vol. 45 ›› Issue (3): 128-132.DOI: 10.13251/j.issn.0254-6051.2020.03.025

激光功率对40CrNiMoA钢表面淬火组织和摩擦磨损性能的影响

杨振¹, 樊湘芳¹, 邱长军¹, 李勇², 柳宁²

1. 南华大学机械工程学院, 湖南衡阳 421001;
2. 衡阳中钢衡重设备有限公司, 湖南衡阳 421001

收稿日期:2019-09-25 出版日期:2020-03-25 发布日期:2020-04-03
通讯作者: 樊湘芳,教授,主要从事金属材料表面改性研究,E-mail:hefanyibang@163.com
作者简介:杨振(1993—),男,硕士研究生,主要从事金属材料表面改性研究,E-mail:515495856@qq.com。
基金资助:
衡阳市科学技术发展计划项目(2018KJ170)

Effect of laser power on quenched microstructure and friction and wear properties of 40CrNiMoA steel

Yang Zhen¹, Fan Xiangfang¹, Qiu Changjun¹, Li Yong², Liu Ning²

1. School of Mechanical Engineering, University of South China, Hengyang Hunan 421001, China;
2. Hengyang Zhonggang Hengzhong Equipment Co., Ltd., Hengyang Hunan 421001, China

Received:2019-09-25 Online:2020-03-25 Published:2020-04-03

摘要/Abstract

摘要：

采用不同激光功率在卷取机卷筒主轴40CrNiMoA钢基材表面进行了激光淬火试验,利用体视显微镜、光学显微镜、显微硬度计和立式万能摩擦磨损试验机等观察和测试试样横截面的宏观组织、表面显微组织、激光相变硬化区的显微硬度和摩擦磨损性能。结果表明:3种不同功率下的激光淬火试样表层组织均得到不同程度的细化,其硬度、摩擦磨损性能较基体均有所提升。其中,当功率为1600 W时,在试样截面能够明显观察到相变硬化区。此时,试样的表层组织最为细致,由细小的针状马氏体、少量残留奥氏体和弥散分布的细小碳化物组成,其表面硬度可达640.3~706.8 HV0.2,约为基体硬度的2.8倍。同时,摩擦因数稳定在0.40~0.60之间,与基体相比降低了50%左右;磨损量1.3 mg,仅为基体的36.1%。在光斑尺寸12 mm×2 mm,扫描速度v=20 mm/s的试验条件下,采用1600 W激光功率对40CrNiMoA钢进行表面激光淬火,得到的试样组织和摩擦磨损性能最优。

关键词: 40CrNiMoA钢, 激光淬火, 激光功率, 显微组织, 摩擦磨损

Abstract:

The surface layer of the coiled spindle main shaft 40CrNiMoA steel base material was tested by laser-quenching with different power. The macroscopic structure of cross-section, surface microstructure, microhardness, and friction and wear properties of the specimens were observed or tested by means of stereo microscope, optical microscope, microhardness tester, vertical universal friction and wear tester. The results show that, the surface structure of the laser hardened specimens at different powers exhibit different levels of refining, and compared with the matrix, the hardness and friction and wear properties are improved. When the power is 1600 W, the laser hardened layer can be clearly observed in the cross-section of the specimens, and the surface layer of the specimens is the most detailed, consisting of fine acicular martensite, a small amount of retained austenite and a finely distributed fine carbide, and the surface hardness can reach 640.3-706.8 HV0.2, which is about 2.8 times of that of the substrate. At the same time, the friction coefficient is stable between 0.40 and 0.60, which is about 50% lower than that of the substrate. The amount of wear is 1.3 mg, which is only 36.1% of the substrate. Under the test conditions of spot size with 12 mm×2 mm, scanning speed with 20 mm/s and laser power with 1600 W, the obtained microstructure and friction and wear properties are optimized after surface laser quenching of 40CrNiMoA steel.

Key words: 40CrNiMoA steel, laser quenching, laser power, microstructure, friction and wear

中图分类号:

杨振, 樊湘芳, 邱长军, 李勇, 柳宁. 激光功率对40CrNiMoA钢表面淬火组织和摩擦磨损性能的影响[J]. 金属热处理, 2020, 45(3): 128-132.

Yang Zhen, Fan Xiangfang, Qiu Changjun, Li Yong, Liu Ning. Effect of laser power on quenched microstructure and friction and wear properties of 40CrNiMoA steel[J]. HTM, 2020, 45(3): 128-132.

参考文献

[1]Mcdanicls R L, White S A, Liaw K, et al. Effects of a laser surface processing induced heat-affect zone on the fatigue behavior of AISI 4340 steel[J]. Material Science and Engineering A, 2008, 485(1): 500-507.
[2]王敬忠, 李科元, 刘阿娇, 等. 40CrNiMo钢国内外研究现状[J]. 钢铁, 2018, 53(5): 1-10.
Wang Jingzhong, Li Keyuan, Liu Ajiao, et al. Research status of 40CrNiMo steel at home and abroad[J]. Iron and Steel, 2018, 53(5): 1-10.
[3]Puchi-Cabrera E S, Staia M H, Quinto D T, et al. Fatigue properties of a SAE 4340 steel coated with TiCN by PAPVD[J]. International Journal of Fatigue, 2007, 29(3): 471-480.
[4]秦仁耀, 周标, 马瑞, 等. 激光熔化沉积修复40CrNiMoA高强钢的组织与性能[J]. 失效分析与预防, 2018, 13(5): 275-280.
Qin Renyao, Zhou Biao, Ma Rui, et al. Microstructure and properties of 40crnimoa high-strength steel repaired by laser melting deposition[J]. Failire Analysis and Prevention, 2018, 13(5): 275-280.
[5]Zhang S, Cong S, Zhao T, et al. Strengthening and application research of carbo-niobiumizing of 40CrNiMo steel[J]. Heat Treatment of Metals, 2012, 37(3): 99-102.
[6]朱跃峰, 尹永晶, 赵旭平, 等. 石油钻采装备用40CrNiMoA钢的冲击性能[J]. 金属热处理, 2005, 30(10): 39-43.
Zhu Yuefeng, Yin Yongjing, Zhao Xuping, et al. Impact property of 40CrNiMoA steel applied in petroleum equipment[J]. Heat Treatment of Metals, 2005, 30(10): 39-43.
[7]支龙, 陈红斌, 袁满, 等. 回火温度对淬火态40CrNiMoA钢组织与力学性能的影响[J]. 热加工工艺, 2018, 47(18): 200-202.
Zhi Long, Chen Hongbin. Yuan Man, et al. Effects of tempering temperature on microstructure and mechanical properties of quenched 40CrNiMoA steel[J]. Hot Working Technology, 2018, 47(18): 200-202.
[8]王敬忠, 刘阿娇, 李科元, 等. 40CrNiMo钢热变形行为及本构方程[J]. 材料热处理学报, 2018, 39(3): 136-143.
Wang Jingzhong, Liu Ajiao, Li Keyuan, et al. Thermal deformation behavior and constitutive equation of 40CrNiMo steel[J]. Transactions of Materials and Heat Treatment, 2018, 39(3): 136-143.
[9]李永兵, 王健, 左玲立, 等. 复杂曲面结构凸轮槽高频感应淬火工艺及组织与性能[J]. 金属热处理, 2010, 35(11): 70-72.
Li Yongbing, Wang Jian, Zuo Lingli, et al. High-frequency induction quenching process and microstructure and properties of cam slot with complex curved-surface[J]. Heat Treatment of Metals, 2010, 35(11): 70-72.
[10]段松, 秦茶, 李碧波. 激光淬火处理后半高速钢的组织及性能[J]. 金属热处理, 2015, 40(9): 76-78.
Duan Song, Qin Cha, Li Bibo. Microstructure and properties of semi-HSS treated by laser quenching[J]. Heat Treatment of Metals, 2015, 40(9): 76-78.
[11]符轲, 张修庆, 续晓霄, 等. 45钢激光淬火工艺优化及性能[J]. 金属热处理, 2017, 42(1): 154-157.
Fu Ke, Zhang Xiuqing, Xu Xiaoxiao, et al. Process optimization and property analysis of 45 steel by laser quenching[J]. Heat Treatment of Metals, 2017, 42(1): 154-157.
[12]程义远, 王勇, 韩彬, 等. 35CrMoA钢激光淬火-渗氮复合处理微观组织与性能[J]. 中国激光, 2010, 37(1): 250-255.
Cheng Yiyuan, Wang Yong, Han Bin, et al. Microstructure and properties of 35CrMoA steel in laser quenching-nitriding[J]. Chinese Journal of Lasers, 2010, 37(1): 250-255.
[13]侯琦, 刘广鑫, 杨光, 等. MoCr铸铁激光淬火组织及磨损性能研究[J]. 应用激光, 2015, 35(6): 657-660.
Hou Qi, Liu Guangxin, Yang Guang, et al. Study on the microstructure and wear property of MoCr cast iron treated by laser quenching[J]. Applied Laser, 2015, 35(6): 657-660.
[14]李刚, 相珺, 况军, 等. GCr15 钢表面激光淬火的组织与性能[J]. 材料热处理学报, 2010, 31(4): 129-132.
Li Gang, Xiang Jun, Kuang Jun, et al. Microstructure and properties of GCr15 steel treated by laser quenching[J]. Transactions of Materials and Heat Treatment, 2010, 31(4): 129-132.
[15]孔德军, 付贵忠, 王文昌, 等. 激光淬火对40CrNiMo摩擦与磨损性能的影响[J]. 中南大学学报(自然科学版), 2014, 45(3): 714-720.
Kong Dejun, Fu Guizhong, Wang Wenchang, et al. Effects of laser quenching on friction and wear properties of 40CrNiMo[J]. Journal of Central South University(Science and Technology), 2014, 45(3): 714-720.

激光功率对40CrNiMoA钢表面淬火组织和摩擦磨损性能的影响

Effect of laser power on quenched microstructure and friction and wear properties of 40CrNiMoA steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[2]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[3]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[4]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[5]	孙凯, 陈研, 杨绍斌. 时效温度对激光选区熔化TC21钛合金微观组织及硬度的影响[J]. 金属热处理, 2022, 47(4): 155-158.
[6]	李梦, 武美萍, 陆佩佩, 赵子硕, 缪小进. 选区激光熔化MnSi₂增强316L不锈钢复合材料的表面质量及耐蚀性能[J]. 金属热处理, 2022, 47(4): 165-170.
[7]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[8]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[9]	王绍灼, 孟晗, 王芬, 樊海卫, 李燕, 唐超. 改善低氧TC4-LC及重熔TC4钛合金性能的热处理工艺[J]. 金属热处理, 2022, 47(4): 204-207.
[10]	石铭霄, 王雄栋, 李敬勇, 杨志东, 茅卫东, 倪慧锋. AISI 410钢膏剂渗硼工艺渗层的组织与性能[J]. 金属热处理, 2022, 47(4): 245-250.
[11]	赵子硕, 武美萍, 缪小进, 崔宸, 龚玉玲. 激光功率对FeCoNiCrMo高熵合金/氧化石墨烯复合涂层组织及耐腐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 251-257.
[12]	张宁, 高星, 王芝林, 蒋波, 刘雅政. 18CrNiMo7-6钢齿轮组织性能异常分析[J]. 金属热处理, 2022, 47(4): 268-273.
[13]	王敬元, 吴松全, 张博华, 辛社伟, 杨义, 王皞, 黄爱军. 固溶时效处理对BT25y钛合金显微组织及硬度的影响[J]. 金属热处理, 2022, 47(3): 14-19.
[14]	孙建, 黄贞益, 李景辉, 王萍. 固溶和时效处理对Fe-Mn-Al-C轻质钢组织和硬度的影响[J]. 金属热处理, 2022, 47(3): 34-38.
[15]	王方军, 刘应龙, 时瑶, 万红, 刘斌斌. 等温退火处理对Inconel 625合金箔材组织和性能的影响[J]. 金属热处理, 2022, 47(3): 77-81.