Effect of shot peening process on surface properties and  wear behavior of 4Cr5Mo2V steel

doi:10.13251/j.issn.0254-6051.2023.12.026

Abstract

Abstract: Effects of different shot peening processes on the surface morphologies and microstructure, mechanical properties, and friction and wear behavior of 4Cr5Mo2V hot work die steel were investigated by using white light interferometer, scanning electron microscope (SEM), X-ray diffractometer (XRD) and residual stress meter. The results show that after carried out 0.4 mmA + 0.2 mmA + 0.1 mmA compound shot peening treatment, the specimen has the strongest strengthening effect, under dislocation strengthening and fine grain strengthening, the surface hardness of the specimen increases from 520 HV0.1 to 601 HV0.1, the peak of the residual stress is -1141 MPa, higher hardness and residual stress could improve the material resistance to adhesion and friction and wear, so that the wear resistance of the material is greatly improved, and the wear rate is reduced by 60.7%. Therefore, this process shall be the best shot peening process.

Key words: shot peening process, 4Cr5Mo2V steel, friction and wear, shot peening strengthening

CLC Number:

TG668

Niu Tong, Wang Xinyu, Wu Xiaochun. Effect of shot peening process on surface properties and wear behavior of 4Cr5Mo2V steel[J]. Heat Treatment of Metals, 2023, 48(12): 153-159.

References

[1]Neubauer F, Merkleina M. Tribological and thermal investigation of modified hot stamping tools[J]. Tribology in Industry, 2019, 41(1): 76-89.
[2]Liu Y, Lin J, Min J, et al. Effect of deep cryogenic treatment on mechanical properties and microstructure of the tool steel CR7V for hot stamping[J]. Journal of Materials Engineering and Performance, 2018, 27(9): 4382-4391.
[3]Zhang Y, Lai F, Qu S, et al. Effect of shot peening on residual stress distribution and tribological behaviors of 17Cr2Ni2MoVNb steel[J]. Applied Surface Science, 2020, 386: 125497.
[4]胡英俊, 黄小波, 高玉魁. 喷丸处理对锆合金微动磨损及抗腐蚀性能的影响[J]. 表面技术, 2020, 49(7): 238-254.
Hu Yingjun, Huang Xiaobo, Gao Yukui. Effect of shot peening on fretting wear and corrosion resistance of zirconium alloy[J]. Surface Technology, 2020, 49(7): 238-254.
[5]Maleki E, Unal O, Kashyzadeh K R. Effects of conventional, severe, over, and re-shot peening processes on the fatigue behavior of mild carbon steel[J]. Surface and Coatings Technology, 2018, 344: 62-74.
[6]Kovacı H, Hacısalihoğlu I·, Yetim A F, et al. Effects of shot peening pre-treatment and plasma nitriding parameters on the structural, mechanical and tribological properties of AISI 4140 low-alloy steel[J]. Surface and Coatings Technology, 2019, 358: 256-265.
[7]Khun N W, Trung P Q, Butler D L. Study on hardness and wear resistance of shot peened AA7075-T6 aluminum alloy[J]. Engineering Research Express, 2021, 3(1): 15-31.
[8]徐松超, 盖鹏涛, 付雪松, 等. 干、湿喷丸强化对TC17钛合金喷丸强化层的影响[J]. 表面技术, 2021, 50(9): 91-98.
Xu Songchao, Gai Pengtao, Fu Xuesong, et al. Influences of dry and wet shot peening process on strengthening layer of TC17 titanium alloy[J]. Surface Technology, 2021, 50(9): 91-98.
[9]孙强, 黄苏起, 蔡著文, 等. 两种热冲压模具用钢的抗拉毛性能[J]. 材料导报, 2021, 35(10): 10152-10157.
Sun Qiang, Huang Suqi, Cai Zhuwen, et al. Anti-galling performance of two hot stamping mould steels[J]. Material Reports, 2021, 35(10): 10152-10157.
[10]吴瑛, 雷丽萍, 曾攀. 喷丸强化对H13钢表面完整性的影响[J]. 锻压技术, 2017, 42(11): 164-171.
Wu Ying, Lei Liping, Zeng Pan. Influence of shot peening on surface integrity of steel H13[J]. Forging and Stamping Technology, 2017, 42(11): 164-171.
[11]付鹏. 高强双相钢喷丸强化及其XRD表征[D]. 上海: 上海交通大学, 2015.
[12]吕鹤婷, 王建明, 刘兴睿. 喷丸残余应力对裂纹闭合效应影响的数值仿真[J]. 中国表面工程, 2016, 29(2): 102-110.
Lü Heting, Wang Jianming, Liu Xingrui. Numerical simulation for residual stress fields of shot-peening on crack closure effects[J]. China Surface Engineering, 2016, 29(2): 102-110.
[13]Ngár T, Ott S, Sanders P G, et al. Dislocations, grain size and planar faults in nanostructured copper determined by high resolution X-ray diffraction and a new procedure of peak profile analysis[J]. Acta Materialia, 1998, 46(10): 3693-3699.
[14]Dutta R K, Petrov R H, Delhez R, et al. The effect of tensile deformation by in situ ultrasonic treatment on the microstructure of low-carbon steel[J]. Acta Materialia, 2013, 61(5): 1592-1602.
[15]Ungár T, Dragomir I, Borbély A. The contrast factors of dislocations in cubic crystals: The dislocation model of strain anisotropy in practice[J]. Journal of Applied Crystallography, 1999, 32(5): 992-1002.
[16]Hall E O. The deformation and ageing of mild Steel: III Discussion of Results[J]. Proceedings of the Physical Society. Section B, 1951, 643(9): 747-752.
[17]李国宾, 关德林, 张明星. 表面纳米化中碳钢在干摩擦条件下的摩擦磨损性能研究[J]. 摩擦学学报, 2008, 28(1): 39-43.
Li Guobin, Guan Delin, Zhang Mingxing. Friction and wear properties of medium carbon steel by means of surface nanocrystallization in dry sliding[J]. Tribology, 2008, 28(1): 39-43.

Effect of shot peening process on surface properties and wear behavior of 4Cr5Mo2V steel

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	He Wei, Wang Yanyan, Shu Linsen. Effect of scanning speed on microstructure and properties of 316L stainless steel coatings by high-speed laser cladding [J]. Heat Treatment of Metals, 2023, 48(8): 248-253.
[2]	Ma Xin, Shi Qiang, Chen Yanzhong, Li Qiang, Zhang Yueting, Zhao Long. Laser quenching process optimization and microstructure and properties of H13 steel [J]. Heat Treatment of Metals, 2023, 48(7): 266-270.
[3]	Tan Shenlu, Zhang Yue, Zhang Mengjiu, Xie Aijun, Shang Jian. Effect of La on microstructure and properties of niobiumized layer on H13 steel [J]. Heat Treatment of Metals, 2023, 48(5): 98-103.
[4]	Qin Chun, Duan Haozhuo, Li Wei. Effect of solution treatment on microstructure and friction and wear properties of Ti-14Al-10Nb alloy [J]. Heat Treatment of Metals, 2023, 48(12): 56-59.
[5]	Guan Lei, Liu Jiaxing, Sun Shibo, Tong Yunxiang. Research progress of NiTi-based bearing alloys [J]. Heat Treatment of Metals, 2023, 48(12): 236-243.
[6]	Du Baoshuai, Mi Chunxu, Wang Xin, Yang Chao, Yang Xinyu, Yan Zhicheng. Effect of austenitizing temperature on friction and wear properties of austempered ductile iron [J]. Heat Treatment of Metals, 2023, 48(11): 149-155.
[7]	Li Yelin, Jia Bo, Shi Zhengliang, Hu Wenxiang, Guan Yunqi, Zheng Huiyun. Friction and wear performance of sulfurized layer on gray cast iron [J]. Heat Treatment of Metals, 2023, 48(10): 266-273.
[8]	Ding Xuxu, Wu Xiaolan, Wang Wei, Rao Mao, Mao Xuejing, Gao Kunyuan, Wei Wu, Huang Hui. Effect of Er on microstructure and wear properties of Al-Zn-Mg alloy [J]. Heat Treatment of Metals, 2023, 48(1): 6-11.
[9]	Liu Lingbo, Yang Guirong, Song Wenming, Li Yamin, Ma Ying. Microstructure and wear performance of Ni-WB₂ composite clad layer [J]. Heat Treatment of Metals, 2023, 48(1): 207-216.
[10]	Yu Zetong, Wang Mingli, Niu Yi, Liu Guanjun. Rare earth induced ion nitriding process of Cr12 steel [J]. Heat Treatment of Metals, 2022, 47(8): 173-176.
[11]	Suo Zhongyuan, Du Yang, Fu Liming, Shan Aidang. Effect of partitioning process on friction and wear properties of 5CrMnNiMo ultra-high strength steel [J]. Heat Treatment of Metals, 2022, 47(7): 134-137.
[12]	Zhou Liuyan, Liu Liguo, Ma Hui, Chen Dongxu. Salt bath vanadium-nitrocarburizing process of AZ31B magnesium alloy [J]. Heat Treatment of Metals, 2022, 47(7): 259-263.
[13]	Shi Shuting, Shu Linsen, He Yajuan, Wang Jiasheng. Effect of laser power on microstructure and properties of clad layer on 27SiMn steel [J]. Heat Treatment of Metals, 2022, 47(5): 194-198.
[14]	Dong Yue, Shu Linsen. Effect of defocusing amount on microstructure and properties of MoS₂ modified Fe-Cr-Mo-Si alloy coating [J]. Heat Treatment of Metals, 2022, 47(5): 246-251.
[15]	Yu Guoqing, Jing Ran, Wang Guodi, Zhang Manxue, Feng Tian, Xie Niansuo. Effect of MAO voltage on friction and wear properties of TC4 alloy oxide film [J]. Heat Treatment of Metals, 2021, 46(11): 126-130.