工程机械用超高强钢的直接淬火-回火工艺及组织性能

doi:10.13251/j.issn.0254-6051.2025.03.008

金属热处理 ›› 2025, Vol. 50 ›› Issue (3): 51-56.DOI: 10.13251/j.issn.0254-6051.2025.03.008

工程机械用超高强钢的直接淬火-回火工艺及组织性能

郑东升¹, 范才河¹, 周顺志¹, 董跃², 夏毅¹

1.湖南工业大学材料与先进制造学院, 湖南株洲 412007;
2.湖南工业大学教务处, 湖南株洲 412007

收稿日期:2024-10-12 修回日期:2025-01-06 出版日期:2025-03-25 发布日期:2025-05-14
作者简介:郑东升(1982—),男,讲师,博士,主要研究方向为先进金属材料制备及其失效机理,E-mail:dongsheng210@163.com
基金资助:
国家自然科学基金(52271177);湖南省科技创新领军人才项目(2021RC4036);国家级大学生创新创业训练计划(S202311535033);湖南省自然科学基金(2025JJ70040,2025JJ70063)

Direct-quenching and tempering process and microstructure-property of ultra-high strength steel for construction machinery

Zheng Dongsheng¹, Fan Caihe¹, Zhou Shunzhi¹, Dong Yue², Xia Yi¹

1. College of Materials and Advanced Manufacturing, Hunan University of Technology, Zhuzhou Hunan 412007, China;
2. Teaching Affairs Office, Hunan University of Technology, Zhuzhou Hunan 412007, China

Received:2024-10-12 Revised:2025-01-06 Online:2025-03-25 Published:2025-05-14

摘要/Abstract

摘要： 借助MMS-200热模拟试验机、光学显微镜(OM)、扫描电镜(SEM)和维氏硬度计研究了830 ℃热变形后的冷速(2~20 ℃/s)、回火温度(150~600 ℃)对直接淬火工程机械用超高强钢微观组织和硬度的影响,并对比了直接淬火-回火工艺和再加热淬火-回火工艺下的微观组织和硬度。结果表明,随着热变形后冷速的增大,粒状贝氏体、上贝氏体消失,自回火马氏体的含量降低,冷速超过5 ℃/s时,微观组织为板条马氏体和自回火马氏体的混合组织;试验钢的硬度逐渐增加,冷速为20 ℃/s时,硬度最大,为509 HV。试验钢直接淬火-回火后,随着回火温度的升高,碳化物的析出位置从马氏体板条内过渡到原始奥氏体晶界和马氏体板条界上,并不断聚集、粗化;试验钢的硬度逐渐减小,当回火温度为150 ℃时,硬度最大,为510 HV。相同回火工艺下,相较于再加热淬火-回火试验钢,直接淬火-回火试验钢中的马氏体板条宽度更小,基体的硬度更高。

关键词: 工程机械用超高强钢, 冷却速度, 直接淬火, 回火温度, 微观组织

Abstract: Effects of cooling rate (2-20 ℃/s) after hot deformation at 830 ℃ and tempering temperature (150-600 ℃) on the microstructure and hardness of direct-quenched ultra-high strength steel for construction machinery were studied by MMS-200 thermomechanical simulator, optical microscope(OM), scanning electron microscope(SEM) and Vickers hardness tester, and the microstructure and hardness of the steel under direct quenching and tempering process were compared with that under reheated quenching and tempering process. The results show that granular bainite and upper bainite disappear and the content of auto-tempered martensite decreases with the increase of cooling rate after hot deformation, and the microstructure is a mixture of lath martensite and auto-tempered martensite when the cooling rate exceeds 5 ℃/s. As the cooling rate increases, the hardness of the tested steel gradually increases, and the maximum hardness is 509 HV at the cooling rate of 20 ℃/s. When the tested steel is directly quenched and tempered, with the increase of tempering temperature, the precipitation position of carbides transits from the inside of martensite lath to the prior austenite grain and martensite lath boundaries, and the carbides continuously aggregate and coarsen. The hardness of the tested steel decreases with the increase of tempering temperature, and the maximum hardness is 510 HV at the tempering temperature of 150 ℃. Compared with reheated quenched and tempered steel, the width of martensite lath in direct quenched and tempered steel is smaller, and the hardness of matrix is higher under the same tempering process.

Key words: ultra-high strength steel for construction machinery, cooling rate, direct quenching, tempering temperature, microstructure

中图分类号:

TG113.25⁺1

郑东升, 范才河, 周顺志, 董跃, 夏毅. 工程机械用超高强钢的直接淬火-回火工艺及组织性能[J]. 金属热处理, 2025, 50(3): 51-56.

Zheng Dongsheng, Fan Caihe, Zhou Shunzhi, Dong Yue, Xia Yi. Direct-quenching and tempering process and microstructure-property of ultra-high strength steel for construction machinery[J]. Heat Treatment of Metals, 2025, 50(3): 51-56.

参考文献

[1] Ali M, Alatarvas T, Komi J, et al. Impact of niobium addition and non-metallic inclusions' characteristics on the microstructure and mechanical properties of low-carbon CrNiMnMoB ultrahigh-strength steel: A comprehensive investigation[J]. Journal of Materials Research and Technology, 2024, 30: 6133-6153.
[2] Keranen L, Nousiainen O, Javaheri V, et al. Mechanical properties of welded ultrahigh-strength S960 steel at low and elevated temperatures[J]. Journal of Constructional Steel Research, 2022, 198(2): 107517.
[3] Mandal A, Karmakar A, Chakrabarti D, et al. Effect of alloying and coiling temperature on the microstructure and bending performance of ultra-high-strength strip steel[J]. Metallurgical and Materials Transactions A, 2018, 49(12): 6359-6374.
[4] Suikkanen P P, Kömi J I. Microstructure, properties and design of direct quenched structural steels[J]. Materials Science Forum, 2014, 783-786: 246-251.
[5] 高朋, 高野, 陈俊, 等. 回火温度对DQ工艺1000 MPa级高强钢组织及性能的影响[J]. 金属热处理, 2019, 44(10): 72-76.
Gao Peng, Gao Ye, Chen Jun, et al. Effect of tempering temperature on microstructure and properties of 1000 MPa high strength steel produced by DQ process[J]. Heat Treatment of Metals, 2019, 44(10): 72-76.
[6] 马长文, 狄国标, 王凯凯, 等. 在线淬火对高强度钢板组织转变及力学性能的影响[J]. 机械工程材料, 2021, 45(5): 34-38.
Ma Changwen, Di Guobiao, Wang Kaikai, et al. Effect of on-line quenching on microstructure transition and mechanical properties of high-strength steel plate[J]. Materials for Mechanical Engineering, 2021, 45(5): 34-38.
[7] 杨雄. 直接淬火960 MPa级高强钢板的组织性能与板形控制研究[D]. 北京: 北京科技大学, 2021.
Yang Xiong. Research study on microstructure and shape control of directly quenched 960 MPa grade high strength steel plate[D]. Beijing: University of Science and Technology Beijing, 2021.
[8] Klein M, Rauch R, Spindler H, et al. Ultra high strength steels produced by thermomechanical hot rolling-advanced properties and applications[J]. Berg-und Hüttenmännische Monatshefte, 2012, 157(3): 108-112.
[9] Saastamoinen A, Kaijalainen A, Heikkal J, et al. The effect of tempering temperature on microstructure, mechanical properties and bendability of direct-quenched low-alloy strip steel[J]. Materials Science and Engineering A, 2018, 730: 284-294.
[10] Esterl R, Sonnleitner M, Weißensteiner I, et al. Influence of quenching conditions on texture and mechanical properties of ultra-high-strength steels[J]. Journal of Materials Science, 2019, 54: 12875-12886.
[11] Huang J M, Li L J, Luo Z C, et al. Improving the ductility of ultrahigh strength lath martensite through heterogeneous carbon distribution[J]. Journal of Materials Research and Technology, 2023, 27: 8209-8215.
[12] Ning D, Dai C R, Wu J L, et al. Carbide precipitation and coarsening kinetics in low carbon and low alloy steel during quenching and subsequently tempering[J]. Materials Characterization, 2021, 176: 111111.

[1]	李申奥, 陈思文, 牛红伟, 朱红倩, 阚允, 江艳, 王健, 赵洪运. 轧制温度对Sc微合金化Al-3.2Cu-1.5Li合金组织和性能的影响[J]. 金属热处理, 2025, 50(3): 1-8.
[2]	王娇娇, 高云哲, 郭泰瑜, 侯伟, 周玉青, 任可飘, 赵林林, 张子悦. 回火时间对深井套管用钢组织性能的影响[J]. 金属热处理, 2025, 50(3): 102-106.
[3]	王惟一, 潘应君, 周乃鹏, 柴锋, 罗小兵. 直接淬火对590 MPa含铜HSLA钢组织演变及力学性能的影响[J]. 金属热处理, 2025, 50(3): 118-124.
[4]	马若曦, 尹宇彬, 邓超, 李子瑜, 张哲临, 丁桦. Fe-18Mn-8Al-1C轻质钢的组织性能及变形机制[J]. 金属热处理, 2025, 50(3): 183-188.
[5]	董恩涛, 滕艾均, 方强, 陈鑫, 代广霖, 康强, 王鹏, 耿乃涛. Ti-38644钛合金热变形行为及组织演变[J]. 金属热处理, 2025, 50(3): 201-207.
[6]	齐加胜, 徐文权. 汽车用中锰钢的研究现状与展望[J]. 金属热处理, 2025, 50(3): 244-249.
[7]	杨宾, 王琳, 申航睿, 冯松科, 李国飞, 刘富强, 方浏昕, 杨林. 热处理温度对盐浴淬火65Mn钢组织与力学性能的影响[J]. 金属热处理, 2025, 50(2): 102-106.
[8]	陈千, 陈正宗, 刘正东, 蔡文河, 姜海峰, 包汉生, 何西扣. 热循环峰值温度对G115钢管热影响区微观组织与性能的影响[J]. 金属热处理, 2025, 50(2): 114-120.
[9]	毕晓勤, 张森, 郑泽远, 齐玉蕾, 付莹, 徐琴. Y添加和热处理对Al-Mg-Si-Y合金组织与性能的影响[J]. 金属热处理, 2025, 50(2): 148-154.
[10]	玄东坡, 郭函, 徐宁, 董林硕, 张健, 李志坚, 刘旭明. 退火温度对1.45%Si无取向硅钢热轧组织及织构的影响[J]. 金属热处理, 2025, 50(2): 181-186.
[11]	夏梓淇, 曹大力, 曹丽华, 赵玲彦, 杨娇娇. 冷却速度对高可靠性SAC-SBN合金及其焊点显微组织的影响[J]. 金属热处理, 2025, 50(2): 218-224.
[12]	于朋翰, 严昊明, 杨帅, 于兴福, 刘永吉, 代友贵. 扩散时间对真空低压渗碳20CrMnTi钢组织与硬度的影响[J]. 金属热处理, 2025, 50(2): 251-255.
[13]	李建国, 贾冬生, 赵银虎, 刘玉宝, 王旭, 赵磊城, 兰岳光. 稀土Ce对32MnMoNiCu铸钢微观组织与力学性能的影响[J]. 金属热处理, 2025, 50(1): 47-52.
[14]	李忠波, 胡海江, 何平, 任可, 袁清, 吴润. 淬火和回火温度对Cr-Mo系耐磨钢组织及力学性能的影响[J]. 金属热处理, 2025, 50(1): 88-96.
[15]	朱晓龙, 王争辉, 王文焱, 谢敬佩, 刁晓刚, 张飞扬. TiC纳米颗粒强化9Cr耐热钢的微观组织及力学性能[J]. 金属热处理, 2025, 50(1): 187-194.

工程机械用超高强钢的直接淬火-回火工艺及组织性能

Direct-quenching and tempering process and microstructure-property of ultra-high strength steel for construction machinery

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价