一种宽回火时间窗口的10.9级螺栓钢组织和性能

doi:10.13251/j.issn.0254-6051.2023.09.039

金属热处理 ›› 2023, Vol. 48 ›› Issue (9): 233-237.DOI: 10.13251/j.issn.0254-6051.2023.09.039

一种宽回火时间窗口的10.9级螺栓钢组织和性能

王娇娇, 刘宏春, 刘泳, 陈红卫, 田志强, 张洪起

河钢材料技术研究院, 河北石家庄 050023

收稿日期:2023-03-27 修回日期:2023-07-29 出版日期:2023-09-25 发布日期:2023-10-25
通讯作者: 刘宏春,助理研究员,硕士,E-mail: liuhongchun0172@163.com
作者简介:王娇娇(1993—),女,助理研究员,硕士,主要研究方向为特殊钢研发及工艺改进,E-mail:wangjiaojiao@hbisco.com。
基金资助:
高端钢铁冶金联合基金(E2022318003)

Microstructure and properties of a grade 10.9 bolt steel with wide tempering time window

Wang Jiaojiao, Liu Hongchun, Liu Yong, Chen Hongwei, Tian Zhiqiang, Zhang Hongqi

HBIS Materials Technology Research Institute, Shijiazhuang Hebei 050023, China

Received:2023-03-27 Revised:2023-07-29 Online:2023-09-25 Published:2023-10-25

摘要/Abstract

摘要： 利用光学显微镜、扫描电镜、透射电镜、洛氏硬度等试验方法研究了一种钒微合金化Si-Mn-Cr系螺栓钢经870 ℃淬火+550 ℃不同时间回火后的微观组织、力学性能。结果表明,870 ℃淬火后试验钢为马氏体板条组织,经550 ℃分别回火40、60、80 min后,均为清晰的马氏体板条组织并伴有细小弥散的碳化物析出。当回火时间在40~80 min时,试验钢的抗拉强度在1081~1120 MPa范围内,屈服强度在993~1013 MPa范围内,断面收缩率在56.0%~56.3%范围内,力学性能稳定,试验钢的拉伸断口均有明显的缩颈现象,起裂源区均为细小韧窝伴有撕裂棱的韧性断裂,综合力学性能良好。因此研究的10.9级螺栓钢回火时间窗口宽泛,并且综合力学性能稳定,进而有利于扩大螺栓钢的使用范围。

关键词: 10.9级螺栓钢, 回火时间, 微观组织, 力学性能, 宽热处理窗口

Abstract: Microstructure and mechanical properties of a vanadium microalloyed Si-Mn-Cr bolt steel after quenching at 870 ℃+tempering at 550 ℃ for different time were studied by means of optical microscope, scanning electron microscope, transmission electron microscope, and Rockwell hardness test. The results show that the microstructure of the tested steel after quenching at 870 ℃ is lath martensite, and the microstructure after tempering at 550 ℃ for 40, 60 and 80 min, respectively, is clear martensie with accompaning by fine dispersed carbide precipitates. When the tempering time is 40-80 min, the tensile strength of the tested steel is 1081-1120 MPa, the yield strength is 993-1013 MPa, and the percentage reduction of area is 56.0%-56.3%, all of which are relatively stable, and the tensile fracture of the tested steel has obvious neck contraction phenomenon. The fracture source areas are all ductile fractures with small dimples and tearing edges, and the comprehensive mechanical properties are good. Therefore, the tempering time window of the 10.9 grade bolt steel is broad, and the comprehensive mechanical properties are stable, which is conducive to expanding the range of use of bolt steel.

Key words: grade 10.9 bolt steel, tempering time, microstructure, mechanical properties, wide heat treatment window

中图分类号:

TG142.1

王娇娇, 刘宏春, 刘泳, 陈红卫, 田志强, 张洪起. 一种宽回火时间窗口的10.9级螺栓钢组织和性能[J]. 金属热处理, 2023, 48(9): 233-237.

Wang Jiaojiao, Liu Hongchun, Liu Yong, Chen Hongwei, Tian Zhiqiang, Zhang Hongqi. Microstructure and properties of a grade 10.9 bolt steel with wide tempering time window[J]. Heat Treatment of Metals, 2023, 48(9): 233-237.

参考文献

[1]惠卫军, 董瀚, 翁宇庆. 高强度螺栓钢的发展动向[J]. 机械工程材料, 2002, 26(11): 1-4, 38.
Hui Weijun, Dong Han, Weng Yuqing. Research and development trends of high strength steel for bolts[J]. Materials for Mechanical Engineering, 2002, 26 (11): 1-4, 38.
[2]李昊, 惠卫军, 王娇娇, 等. Cu元素对42CrMoV高强度螺栓钢在模拟大气腐蚀环境下腐蚀行为的影响[J]. 材料保护, 2020, 53(11): 13-21.
Li Hao, Hui Weijun, Wang Jiaojiao, et al. Effect of Cu element on the corrosion behavior of 42CrMoV high strength bolt steel in simulated weathering environment[J]. Materials Protection, 2020, 53(11): 13-21.
[3]陶晓燕, 沈家华, 史志强. 我国钢桥高强度螺栓连接的发展历程及展望[J]. 铁道建筑, 2017, 57(9): 1-4.
Tao Xiaoyan, Shen Jiahua, Shi Zhiqiang. Development history and prospect of high strength bolt connection of steel bridge in China[J]. Railway Engineering, 2017, 57(9): 1-4.
[4]张先鸣. 16Cr16Ni2MoNb耐热螺栓钢的热处理工艺研究[J]. 金属加工: 热加工, 2009(5): 32-33.
[5]赵楠, 穆海玲, 周丽萍, 等. 35CrMoA钢连杆螺栓断裂失效分析[J]. 金属热处理, 2008, 33(9): 111-114.
Zhao Nan, Mu Hailin, Zhou Liping, et al. Failure analysis of 35CrMoA steel connecting-rod bolt[J]. Heat Treatment of Metals, 2008, 33(9): 111-114.
[6]李昊. Cu和Ni元素对高强度螺栓钢耐候性和延迟断裂的影响[D]. 北京: 北京交通大学, 2018.
Li Hao. Effect of Cu and Ni on corrosion resistance and delayed fracture of high strength bolt steel[D]. Beijing: Beijing Jiaotong University, 2018.
[7]Omura T. Hydrogen entry and its effect on delayed fracture susceptibility of high strength steel bolts under atmospheric corrosion[J]. ISIJ International, 2012, 52(2): 267-273.
[8]Nanninga N, Grochowsi J, Heldt L, et al. Role of microstructure, composition and hardness in resisting hydrogen embrittlement of fastener grade steels[J]. Corrosion Science, 2010, 52: 1237-1246.
[9]刘浩然. 热处理工艺对耐候螺栓钢组织和力学性能的影响[D]. 秦皇岛: 燕山大学, 2018.
Liu Haoran. Effect of heat treatment on microstructure and mechanical properties of weathering bolt steel[D]. Qinhuangdao: Yanshan University, 2018.
[10]雷鸣. 钒合金化中锰钢组织及力学性能研究[D]. 北京: 北京交通大学, 2019.
Lei Ming. Study of microstructure and mechanical properties of V-alloyed medium Mn steel[D]. Beijing: Beijing Jiaotong University, 2019.
[11]Hui W J, Zhang Y J, Zhao X L, et al. Very high cycle fatigue properties of Cr-Mo low alloy steel containing V-rich MC type carbides[J]. Materials Science & Engineering A, 2016, 651: 311-320.
[12]王占花, 惠卫军, 谢志奇, 等. 回火对钒钛微合金化Mn-Cr系贝氏体型非调质钢组织和性能的影响[J]. 金属学报, 2020, 56(11): 1441-1451.
Wang Zhanhua, Hui Weijun, Xie Zhiqi, et al. Effects of tempering temperature on microstructure and mechanical properties of a Mn-Cr type bainitic forging steel[J]. Acta Metallurgica Sinica, 2020, 56(11): 1441-1451.
[13]Kihira H, Ito S, Mizoguchi S, et al. Creation of alloy design concept for anti air-born salinity weathering steel[J]. Zairyo-to-Kankyo, 2000, 49(1): 30-40.

[1]	袁志钟, 王梦飞, 张伯承, 段旭斌, 李表敏, 杨海峰, 罗锐, 程晓农. 冷作模具钢SKD11的热处理增韧技术[J]. 金属热处理, 2023, 48(9): 1-7.
[2]	孙博, 聂佳民, 李晓丹, 何长树. 强制冷却和低温时效对2198-T3/7A04-T6异种铝合金FSW接头组织及性能的影响[J]. 金属热处理, 2023, 48(9): 8-13.
[3]	王毅, 韩杰, 刘超, 邓玲蕊, 李辉, 许荣昌. DQ-T工艺对1000 MPa级高强钢组织和性能的影响[J]. 金属热处理, 2023, 48(9): 30-34.
[4]	韩伟松, 杜峰, 李建锋, 朱宝辉, 沈立华, 刘意, 王鹏. 变形量对Ti80G合金力学性能的影响[J]. 金属热处理, 2023, 48(9): 95-98.
[5]	宋操, 王晓东, 包喜荣, 陈林, 汤雪娇. Ce对30MnNbRE钢淬火回火微观组织和力学性能的影响[J]. 金属热处理, 2023, 48(9): 143-149.
[6]	李文刚, 炊鹏飞, 程尊鹏, 李春梅, 景然, 李江华, 廖仲尼. 硼含量对Ti-Zr-Nb-B合金显微组织及性能的影响[J]. 金属热处理, 2023, 48(9): 157-164.
[7]	谢尚恒, 孙有平, 朱嘉欣, 方德俊. 微量Zr对深冷轧制Al-Cu-Mg合金微观组织及性能的影响[J]. 金属热处理, 2023, 48(9): 174-179.
[8]	王英虎. 硫含量对Y12Cr18Ni9易切削钢中硫化物形态及性能的影响[J]. 金属热处理, 2023, 48(9): 183-190.
[9]	李鑫, 武志广, 赵吉庆, 杨钢. 20Cr1Mo1VTiB螺栓钢高温长期时效后的组织演变及力学性能[J]. 金属热处理, 2023, 48(9): 197-202.
[10]	张志春, 温佳, 陈国瑞, 吴广辉, 翁泽钜, 顾开选. 低合金耐磨钢的热处理工艺及力学性能[J]. 金属热处理, 2023, 48(9): 220-224.
[11]	梁恩溥, 徐乐, 杨勇, 王毛球. Ni含量对NiAl-Cu强化40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2023, 48(8): 1-7.
[12]	牛旭, 刘越, 王灼, 张雅静, 刘平祥. 钒含量对秸秆膨化机螺杆用Cr20高铬铸铁组织与性能的影响[J]. 金属热处理, 2023, 48(8): 8-15.
[13]	吴洋, 钱亚锋, 赵言辉. Al含量及时效时间对Mg-Al系镁合金力学性能和阻尼能力的影响[J]. 金属热处理, 2023, 48(8): 30-34.
[14]	孙晓冉, 王程明, 赵楠, 白丽娟, 郑文跃. 4330-Nb抽油杆用钢的连续冷却转变特性分析[J]. 金属热处理, 2023, 48(8): 42-46.
[15]	施峰, 姚伟民, 沈俭, 殷春宏, 曹琦, 洪亚光, 许辉, 丁阳. 固溶处理对长期服役燃机透平叶片组织和力学性能的影响[J]. 金属热处理, 2023, 48(8): 99-105.

一种宽回火时间窗口的10.9级螺栓钢组织和性能

Microstructure and properties of a grade 10.9 bolt steel with wide tempering time window

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价