热处理工艺对5Cr5Mo2V钢组织与性能的影响

doi:10.13251/j.issn.0254-6051.2021.02.010

金属热处理 ›› 2021, Vol. 46 ›› Issue (2): 55-60.DOI: 10.13251/j.issn.0254-6051.2021.02.010

热处理工艺对5Cr5Mo2V钢组织与性能的影响

殷军伟^1,2, 周健², 蒋业华¹, 迟宏宵², 林鹏²

1.昆明理工大学材料科学与工程学院, 云南昆明 650093;
2.钢铁研究总院特殊钢研究所, 北京 100081

收稿日期:2020-07-16 出版日期:2021-02-25 发布日期:2021-05-08
通讯作者: 周健,高级工程师,博士,E-mail:zhou-jian-168@163.com
作者简介:殷军伟(1989—),男,硕士,主要研究方向为工模具钢的研制和开发,E-mail:610631308@qq.com。

Effect of heat treatment process on microstructure and properties of 5Cr5Mo2V steel

Yin Junwei^1,2, Zhou Jian², Jiang Yehua¹, Chi Hongxiao², Lin Peng²

1. Faculty of Materials Science and Engineering, Kunming University of Science and Technology, Kunming Yunnan 650093, China;
2. Special Steels Research Institute, Central Iron and Steel Research Institute, Beijing 100081, China

Received:2020-07-16 Online:2021-02-25 Published:2021-05-08

摘要/Abstract

摘要： 利用洛氏硬度计及场发射扫描电镜等研究了奥氏体化温度和回火温度对热锻模具用钢5Cr5Mo2V组织和性能的影响。结果表明:试验钢经过不同温度的淬火和回火处理后,组织均为回火马氏体+残留奥氏体+碳化物。当5Cr5Mo2V钢在920~1030 ℃淬火时,随淬火温度升高硬度值增加并于1030 ℃达到最大值62.53 HRC,之后硬度值趋于稳定,且在1030 ℃淬火时晶粒较为细小,超过1030 ℃淬火晶粒开始粗化;试验钢在480~550 ℃回火时,硬度值随回火温度升高逐渐增加,并于550 ℃出现二次硬化峰值,但在此温度下试验钢的冲击性能为最低,此后随回火温度升高冲击性能逐渐增加,当回火温度为600 ℃时,试验钢在维持较高硬度(49 HRC)的同时,冲击吸收能量可达21 J,故5Cr5Mo2V钢的最佳热处理工艺为:1030 ℃淬火30 min后油冷,随后在600 ℃回火(2 h)2次空冷。

关键词: 5Cr5Mo2V钢, 热处理, 显微组织, 力学性能

Abstract: Effects of austenitizing temperature and tempering temperature on microstructure and properties of the 5Cr5Mo2V steel for hot forging die were studied by Rockwell hardness tester and field emission scanning electron microscopy. The results show that after different quenching and tempering treatments, the microstructure of all the tested steel specimens is composed of tempered martensite, retained austenite and carbides. When quenched at 920-1030 ℃, the hardness of the 5Cr5Mo2V steel increases with the increase of quenching temperature and reaches the maximum value of 62.53 HRC at 1030 ℃, and then the hardness tends to be stabilized when quenched above 1030 ℃. The grains are finer when quenched at 1030 ℃, but the grains start to coarsen when the quenching temperature exceeds 1030 ℃. As tempered at 480-550 ℃, the hardness gradually increases with the increase of tempering temperature and a secondary hardening peak appears at 550 ℃. The impact absorbed energy of the tested steel is the lowest at 550 ℃, but when the tempering temperature is higher than 550 ℃, the impact properties of the tested steel gradually increase. When the tempering temperature is 600 ℃, the steel maintains a relatively high hardness (49 HRC) and the impact absorbed energy can reach 21 J. It is concluded that the optimum heat treatment process for the 5Cr5Mo2V steel is quenching at 1030 ℃ for 30 min with oil cooling and then tempering twice at 600 ℃ for 2 h with air cooling.

Key words: 5Cr5Mo2V steel, heat treatment, microstructure, mechanical properties

中图分类号:

殷军伟, 周健, 蒋业华, 迟宏宵, 林鹏. 热处理工艺对5Cr5Mo2V钢组织与性能的影响[J]. 金属热处理, 2021, 46(2): 55-60.

Yin Junwei, Zhou Jian, Jiang Yehua, Chi Hongxiao, Lin Peng. Effect of heat treatment process on microstructure and properties of 5Cr5Mo2V steel[J]. Heat Treatment of Metals, 2021, 46(2): 55-60.

参考文献

[1] 王树奇,崔向红.热锻模具的韧性要求[J].中国机械工程,2004,15(8):90-93.
Wang Shuqi,Cui Xianghong.Toughness requirements of hot-forging dies[J].Chinese Journal of Mechanical Engineering,2004,15(8):90-93.
[2] 王运炎,叶尚川.机械工程材料[M].北京:机械工业出版社,2004:174-176.
[3] 徐文晓,张满,杨昌群,等.热锻模耐磨耐冷热疲劳堆焊焊条的研制[J].汽车工艺与材料,2004(8):12-14.
Xu Wenxiao,Zhang Man,Yang Changqun,et al.Development of build-up welding rod used for wear-resistance and cold-heat fatigue resistance hot forging die[J].Automobile Technology &Material,2004(8):12-14.
[4] 李月恩,赵军,王维.热作模具表面失效与模具寿命关系研究[J].锻压技术,2009,34(2):91-93.
Li Yue'en,Zhao Jun,Wang Wei.Research on relationship between mold surface failure and life[J].Forging and Stamping Technology,2009,34(2):91-93.
[5] 董耕野,何孝美.大型热锻模高温淬火工艺初探[J].机电工程技术,2007,36(9):18-20.
Dong Gengye,He Xiaomei.Preliminary study on high temperature quenching process of large hot forging die[J].Mechatronic Engineering Technology,2007,36(9):18-20.
[6] 王孟,宝志坚.汽车轴类热锻模具的失效形式与分析[J].中国工程机械学报,2008,6(3):364-369.
Wang Meng,Bao Zhijian.Deficiency formation and analysis on automotive axle heat-forged mould[J].Chinese Journal of Mechanical Engineering,2008,6(3):364-369.
[7] 潘晓华,朱祖昌.H13热作模具钢的化学成分及其改进和发展的研究[J].模具制造,2006(4):72-84.
Pan Xiaohua,Zhu Zuchang.The study of the chemical composition and improvement and development for the H13 hot work die &mold steel[J].Mold Manufacturing,2006(4):72-84.
[8] 金欣,周健.Mo-W-Co系高热强性热锻模具钢的组织与性能[J].金属热处理,2018,43(2):8-14.
Jin Xin,Zhou Jian.Microstructure and mechanical properties of Mo-W-Co high hot-strength hot-work die steels[J].Heat Treatment of Metals,2018,43(2):8-14.
[9] 张岩,赵爱民.热处理工艺对Cr8钢组织与性能的影响[J].金属热处理,2016,41(1):79-84.
Zhang Yan,Zhao Aimin.Effect of heat treatment on microstructure and properties of Cr8 steel[J].Heat Treatment of Metals,2016,41(1):79-84.
[10] 周健.提高热作模具用H13钢性能的研究[D].昆明:昆明理工大学,2009.
Zhou Jian.Research on improving the performance of H13 steel for hot work die[D].Kunming:Kunming University of Science and Technology,2009.
[11] 张春基,河镇哲,马永庆. Cr-W-Mo-V-Si 工模具钢热处理时碳化物的转变[J].金属热处理,2001,26(4):24-26.
Zhang Chunji,He Zhengzhe,Ma Yongqing.Carbides transform in Cr-W-Mo-V-Si die steel during heat treatment[J].Heat Treatment of Metals,2001,26(4):24-26.
[12] 孙梦龙,谢春生.Cr12模具钢热处理工艺及耐磨性能[J].材料热处理学报,2015,36(5):139-143.
Sun Menglong,Xie Chunsheng.Heat treatment process and wear resistant property of Cr12 die steel[J].Transactions of Materials and Heat Treatment,2015,36(5):139-143.
[13] 鲍俭,杨卯生,王华昆.热处理工艺对20Cr14Co12Mo5轴承钢力学性能的影响[J].钢铁,2010,45(1):91-95.
Bao Jian,Yang Maosheng,Wang Huakun.Effect of heat treatment on mechanical properties of bearing steel 20Cr14Co12Mo5[J].Iron and Steel,2010,45(1):91-95.
[14] Xia Z X,Zhang C,Lan H,et al.Effect of magnetic field on interfacial energy and precipitation behavior of carbides in reduced activation steels[J].Materials Letters,2011,65(6):937-939.
[15] Speich G R,Leslie W C.Tempering of steel[J].Metallurgical Transactions,1972,3(5):1043-1054.
[16] Chen J,Mo W,Wang P,et al.Effects of tempering temperature on the impact toughness of steel 42CrMo[J].Acta Metallurgica Sinica,2012,48(10):1186-1193.
[17] 肖茂果,李东辉,吕新杨,等.热处理对高Cr-Co-Mo轴承钢组织与性能的影响[J].材料热处理学报,2018,39(8):75-80.
Xiao Maoguo,Li Donghui,Lü Xinyang,et al.Effects of heat treatment on microstructure and properties of a high Cr-Co-Mo alloyed heat resistant bearing steel[J].Transactions of Materials and Heat Treatment,2018,39(8):75-80.

热处理工艺对5Cr5Mo2V钢组织与性能的影响

Effect of heat treatment process on microstructure and properties of 5Cr5Mo2V steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张子延, 陈君, 陈晓亚, 李全安, 刘建鑫. 固溶时效处理对Mg-4Sm-3Gd-0.5Zr合金显微组织和耐蚀性能的影响[J]. 金属热处理, 2022, 47(4): 10-16.
[2]	梁恩溥, 徐乐, 杨勇, 王毛球. 添加Al、Cu对40CrNi3MoV钢组织和力学性能的影响[J]. 金属热处理, 2022, 47(4): 17-23.
[3]	祁晓亮, 李岩, 定巍, 赵增武. 含Al中锰TRIP钢原始组织对临界退火后组织与力学性能的影响[J]. 金属热处理, 2022, 47(4): 24-29.
[4]	陈保安, 张静媛, 祝志祥, 韩钰, 潘学东, 张磊, 陈素红. 化学成分对高强Al-Mg-Si合金组织和性能的影响[J]. 金属热处理, 2022, 47(4): 30-38.
[5]	陈连生, 张露友, 田亚强, 杨子旋, 李红斌, 潘红波, 魏英立. 低碳高强舰船用钢的CCT曲线及其组织性能[J]. 金属热处理, 2022, 47(4): 63-68.
[6]	王云龙, 余伟, 张昳, 史佳新, 李明辉. 奥氏体化温度对贝氏体钢等温转变及力学性能的影响[J]. 金属热处理, 2022, 47(4): 80-85.
[7]	骆再斌, 范子泽, 彭振. 轻质高熵合金的研究进展[J]. 金属热处理, 2022, 47(4): 100-107.
[8]	李立, 曾艳, 吴晓春. 4Cr5Mo2VCo钢的热处理工艺优化[J]. 金属热处理, 2022, 47(4): 133-140.
[9]	吕杰晟, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. S32205双相不锈钢冷轧退火组织转变及强塑化机理分析[J]. 金属热处理, 2022, 47(4): 141-145.
[10]	王琪, 吴光亮. 回火温度对1100 MPa级高强钢组织与性能的影响[J]. 金属热处理, 2022, 47(4): 146-150.
[11]	孙凯, 陈研, 杨绍斌. 时效温度对激光选区熔化TC21钛合金微观组织及硬度的影响[J]. 金属热处理, 2022, 47(4): 155-158.
[12]	张骥俊, 邢彦锋, 曹菊勇. 超声振动对CMT电弧增材制造铝合金组织与性能的影响[J]. 金属热处理, 2022, 47(4): 159-164.
[13]	刘文彬, 乔龙阳, 潘新宇, 程格, 李爱娜, 裴新军. 淬火温度对刀剪用M390粉末冶金不锈钢组织和性能的影响[J]. 金属热处理, 2022, 47(4): 189-195.
[14]	王瑞琴, 葛鹏, 廖强, 侯鹏, 刘宇. 固溶冷却方式对短时用高温钛合金板材组织和性能的影响[J]. 金属热处理, 2022, 47(4): 196-198.
[15]	王方军, 王东哲, 万红, 时瑶, 沈涛. 热处理和冷变形量对定膨胀合金4J32C线膨胀系数的影响[J]. 金属热处理, 2022, 47(4): 199-203.